250+ TOP MCQs on Evaporators – Heat Transfer Coefficients and Answers

Heat Transfer Operations Questions and Answers for Entrance exams on “Evaporators – Heat Transfer Coefficients”.

1. If the evaporator operates at very high liquid velocity so that the boiling occurs at the top end of the tube, which one of the following correlation can be used?
a) h_iD ⁄ K_pure = 0.003 Re^0.8 Pr^0.4
b) h_iD ⁄ K_pure = 0.027 Re^0.8 Pr^0.4
c) h_iD ⁄ K_solution = 0.0278 Re^0.8 Pr^0.4
d) h_iD ⁄ K_solution = 0.003 Re^0.8 Pr^0.4

Answer: c
Clarification: If the evaporator operates at a higher velocity and the boiling occurs at the top of the tube, then the equation we must use is h_iD ⁄ K_solution = 0.0278 Re^0.8 Pr^0.4 and not Sieder tate as the working conditions are different for heat exchangers.

2. If the evaporator operates at very high liquid velocity so that the boiling occurs at the top end of the tube, then we use the given relation.
h_iD ⁄ K=0.0278 Re^0.8 Pr^0.4
What is the term K here?
a) Solution thermal conductivity
b) Solvent thermal conductivity
c) Wall thermal conductivity
d) Film thermal conductivity

Answer: a
Clarification: If the evaporator operates at a higher velocity and the boiling occurs at the top of the tube, then the equation we must use is h_iD ⁄ K_solution = 0.0278 Re^0.8 Pr^0.4, where K is the Solution Thermal Conductivity. We do not use Sieder tate equation because the working conditions are different than heat exchangers.

3. The heat transfer coefficient for rising film and falling film evaporators is same because they can be used in the same setup.
a) True
b) False

Answer: b
Clarification: The setup of rising film and falling film might be the same but the film orientation is different for both the setups and hence the heat transfer coefficients too.

4. If the Reynold’s number is 24000 and the Prantl number = 4.70. Then what is the value of Nusselt number?
a) 164.8
b) 164.0
c) 163.8
d) 165.2

Answer: a
Clarification: we use the formula, Nu=0.0278 Re^0.8 Pr^0.4=0.0278×(24000)^0.8×(4.7)^0.4=164.8.

5. In the given formula for overall heat transfer coefficient in Rising film evaporators, What is the term h_OD?
(frac{1}{U}=frac{1}{ho}+frac{1}{h_{OD}}+(frac{Do}{Di})(frac{1}{h_{ID}})+ (frac{Do}{Di})(frac{1}{hi}))
a) Outside dirt coefficient
b) Inside dirt coefficient
c) Outside film heat transfer coefficient
d) Inside film heat transfer coefficient

Answer: a
Clarification: The given equation represents the overall heat transfer coefficient of a rising film evaporator under the condition of fouling and hence the terms h_ID is inside dirt factor and h_OD as the outside dirt factor.

6. Find the value of Residence time if we have a feed of 30kg/hr at 25℃ and with evaporator consumption as 10kg/hr?
Evaporator Volume = 5L
Latent heat of vaporization of water = 2,260 kJ/kg
Specific heat capacity = 6 KJ/Kg K
Average density of solution = 1.2Kg/L
a) 0.2hr
b) 0.3hr
c) 0.4hr
d) 0.5hr

Answer: a
Clarification: The mass flow rate = 30kg/hr, hence the volume flow rate = 30/1.2 = 25L/hr. Thus, as the volume of the evaporator is 5L, residence time = 5/25 = 0.2hr.

7. When the flow velocity of the fluid increases the temperature plot maxima shifts towards __________
a) Steam exit
b) Middle of the tube
c) Feed inlet
d) Feed exit

Answer: d
Clarification: As the flow velocity of the fluid increases, the liquid temperature reaches its maxima when the liquid is about to leave hence the maxima is at the feed exit. At higher velocity the temperature raise is less and the liquid boils near the top of the tube.

8. The liquid temperature in the tubes increases up to certain height and then the temperature decreases due to ___________
a) Loss of superheat
b) Loss of pressure
c) Concentration increase
d) Concentration decrease

Answer: a
Clarification: As the liquid reaches its final stage in the evaporator, its concentration is so high that is hardly releases any vapour and hence its temperature decreases. The steam too has by then condensed completely.

9. What is the real temperature driving force of the evaporator in the given diagram?
a) T_BP – T_w
b) T_W – T_BP
c) T_W – T_steam
d) T_steam – T_BP

Answer: d
Clarification: The real temperature driving force is T_steam – T_BP because T_w is just the pure water boiling point which is not involved in the process, rather the temperature of steam and fluid is all that is of design concern.

10. When the flow rate of the fluid decreases the temperature plot shifts towards __________
a) Steam exit
b) Middle of the tube
c) Feed inlet
d) Feed exit

Answer: b
Clarification: As the flow velocity of the fluid decreases, the liquid temperature reaches its maxima when the liquid is at about the middle of the tube hence the maxima is at the middle little bit near the steam inlet. At higher velocity the temperature raise is less and the liquid boils near the top of the tube.