300+ TOP Polyphase Induction Motors MCQs and Answers

Polyphase Induction Motors Multiple Choice Questions

1. Which of the following component is usually fabricated out of silicon steel ?
(a) Bearings
(b) Shaft
(c) Statorcore
(d) None of the above
Answer: c

2. The frame of an induction motor is usually made of
(a) silicon steel
(b) cast iron
(c) aluminium
(d) bronze
Answer: b

3. The shaft of an induction motor is made of
(a) stiff
(b) flexible
(c) hollow
(d) any of the above
Answer: a

4. The shaft of an induction motor is made of
(a) high speed steel
(b) stainless steel
(c) carbon steel
(d) cast iron
Answer: c

5. In an induction motor, no-load the slip is generally
(a) less than 1%
(b) 1.5%
(c) 2%
(d) 4%
Answer: a

6. In medium sized induction motors, the slip is generally around
(a) 0.04%
(b) 0.4%
(c) 4%
(d) 14%
Answer: c

7. In squirrel cage induction motors, the rotor slots are usually given slight skew in order to
(a) reduce windage losses
(b) reduce eddy currents
(c) reduce accumulation of dirt and dust
(d) reduce magnetic hum
Answer: d

8. In case the air gap in an induction motor is increased
(a) the magnetising current of the rotor will decrease
(b) the power factor will decrease
(c) speed of motor will increase
(d) the windage losses will increase
Answer: b

9. Slip rings are usually made of
(a) copper
(b) carbon
(c) phospor bronze
(d) aluminium
Answer: c

10. A 3-phase 440 V, 50 Hz induction motor has 4% slip. The frequency of rotor e.m.f. will be
(a) 200 Hz
(b) 50 Hz
(c) 2 Hz
(d) 0.2 Hz
Answer: c

11. In Ns is the synchronous speed and s the slip, then actual running speed of an induction motor will be
(a) Ns
(b) s.N,
(c) (l-s)Ns
(d) (Ns-l)s
Answer: c

12. The efficiency of an induction motor can be expected to be nearly
(a) 60 to 90%
(b) 80 to 90%
(c) 95 to 98%
(d) 99%
Answer: b

13. The number of slip rings on a squirrel cage induction motor is usually
(a) two
(b) three
(c) four
(d) none
Answer: d

14. The starting torque of a squirrel-cage induction motor is
(a) low
(b) negligible
(c) same as full-load torque
(d) slightly more than full-load torque
Answer: a

15. A double squirrel-cage induction motor has
(a) two rotors moving in oppsite direction
(b) two parallel windings in stator
(c) two parallel windings in rotor
(d) two series windings in stator
Answer: c

16. Star-delta starting of motors is not possible in case of
(a) single phase motors
(b) variable speed motors
(c) low horse power motors
(d) high speed motors
Answer: a

17. The term ‘cogging’ is associated with
(a) three phase transformers
(b) compound generators
(c) D.C. series motors
(d) induction motors
Answer: d

18. In case of the induction motors the torque is
(a) inversely proportional to (Vslip)
(b) directly proportional to (slip)2
(c) inversely proportional to slip
(d) directly proportional to slip
Answer: d

19. An induction motor with 1000 r.p.m. speed will have
(a) 8 poles
(b) 6 poles
(c) 4 poles
(d) 2 poles
Answer: b

20. The good power factor of an induction motor can be achieved if the average flux density in the air gap is
(a) absent
(b) small
(c) large
(d) infinity
Answer: b

21. An induction motor is identical to
(a) D.C. compound motor
(b) D.C. series motor
(c) synchronous motor
(d) asynchronous motor
Answer: d

22. The injected e.m.f. in the rotor of induction motor must have
(a) zero frequency
(b) the same frequency as the slip frequency
(c) the same phase as the rotor e.m.f.
(d) high value for the satisfactory speed control
Answer: b

23. Which of the following methods is easily applicable to control the speed of the squirrel-cage induction motor ?
(a) By changing the number of stater poles
(b) Rotor rheostat control
(c) By operating two motors in cascade
(d) By injecting e.m.f. in the rotor circuit
Answer: a

24. The crawling in the induction motor is caused by
(a) low voltage supply
(b) high loads
(c) harmonics developed in the motor
(d) improper design of the machine
(e) none of the above
Answer: c

25. The auto-starters (using three auto transformers) can be used to start cage induction motor of the following type
(a) star connected only
(b) delta connected only
(c) (a) and (b) both
(d) none of the above
Answer: c

26. The torque developed in the cage induction motor with auto starter is
(a) k/torque with direct switching
(6) K x torque with direct switching
(c) K2 x torque with direct switching
(d) k2/torque with direct switching
Answer: c

27. When the equivalent circuit diagram of double squirrel-cage induction motor is constructed the two cages can be considered
(a) in series
(b) in parallel
(c) in series-parallel
(d) in parallel with stater
Answer: b

28. It is advisable to avoid line-starting of induction motor and use starter because
(a) motor takes five to seven times its full load current
(b) it will pick-up very high speed and may go out of step
(c) it will run in reverse direction
(d) starting torque is very high
Answer: a

29. Stepless speed control of induction motor is possible by which of the following methods ?
(a) e.m.f. injection in rotor eueuit
(b) Changing the number of poles
(c) Cascade operation
(d) None of the above
Answer: b

30. Rotor rheostat control method of speed control is used for
(a) squirrel-cage induction motors only
(b) slip ring induction motors only
(c) both (a) and (b)
(d) none of the above
Answer: b

31. In the circle diagram for induction motor, the diameter of the circle represents
(a) slip
(b) rotor current
(c) running torque
(d) line voltage
Answer: b

32. For which motor the speed can be controlled from rotor side ?
(a) Squirrel-cage induction motor
(b) Slip-ring induction motor
(c) Both (a) and (b)
(d) None of the above
Answer: b

33. If any two phases for an induction motor are interchanged
(a) the motor will run in reverse direction
(b) the motor will run at reduced speed
(c) the motor will not run
(d) the motor will burn
Answer: a

34. An induction motor is
(a) self-starting with zero torque
(b) self-starting with high torque
(c) self-starting with low torque
(d) non-self starting
Answer: c

35. The maximum torque in an induction motor depends on
(a) frequency
(b) rotor inductive reactance
(c) square of supply voltage
(d) all of the above
Answer: d

36. In three-phase squirrel-cage induction motors
(a) rotor conductor ends are short-circuited through slip rings
(b) rotor conductors are short-circuited through end rings
(c) rotor conductors are kept open
(d) rotor conductors are connected to insulation
Answer: b

37. In a three-phase induction motor, the number of poles in the rotor winding is always
(a) zero
(b) more than the number of poles in stator
(c) less than number of poles in stator
(d) equal to number of poles in stator
Answer: d

38. DOL starting of induction motors is usually restricted to
(a) low horsepower motors
(b) variable speed motors
(c) high horsepower motors
(d) high speed motors
Answer: a

39. The speed of a squirrel-cage induction motor can be controlled by all of the following except
(a) changing supply frequency
(b) changing number of poles
(c) changing winding resistance
(d) reducing supply voltage
Answer: c

40. The ‘crawling” in an induction motor is caused by
(a) high loads
(6) low voltage supply
(c) improper design of machine
(d) harmonics developed in the motor
Answer: d

41. The power factor of an induction motor under no-load conditions will be closer to
(a) 0.2 lagging
(b) 0.2 leading
(c) 0.5 leading
(d) unity
Answer: a

42. The ‘cogging’ of an induction motor can be avoided by
(a) proper ventilation
(b) using DOL starter
(c) auto-transformer starter
(d) having number of rotor slots more or less than the number of stator slots (not equal)
Answer: d

43. If an induction motor with certain ratio of rotor to stator slots, runs at 1/7 of the normal speed, the phenomenon will be termed as
(a) humming
(b) hunting
(c) crawling
(d) cogging
Answer: c

44. Slip of an induction motor is negative when
(a) magnetic field and rotor rotate in opposite direction
(b) rotor speed is less than the synchronous speed of the field and are in the same direction
(c) rotor speed is more than the synchronous speed of the field and are in the same direction
(d) none of the above
Answer: c

45. Size of a high speed motor as compared to low speed motor for the same H.P. will be
(a) bigger
(b) smaller
(c) same
(d) any of the above
Answer: b

46. A 3-phase induction motor stator delta connected, is carrying full load and one of its fuses blows out. Then the motor
(a) will continue running burning its one phase
(b) will continue running burning its two phases
(c) will stop and carry heavy current causing permanent damage to its winding
(d) will continue running without any harm to the winding
Answer: a

47. A 3-phase induction motor delta connected is carrying too heavy load and one of its fuses blows out. Then the
motor
(a) will continue running burning its one phase
(b) will continue running burning its two phase
(c) will stop and carry heavy current causing permanent damage to its winding
(d) will continue running without any harm to the winding
Answer: c

48. Low voltage at motor terminals is due to
(a) inadequate motor wiring
(b) poorely regulated power supply
(c) any one of the above
(d) none of the above
Answer: c

49. In an induction motor the relationship between stator slots and rotor slots is that
(a) stator slots are equal to rotor slots
(b) stator slots are exact multiple of rotor slots
(c) stator slots are not exact multiple of rotor slots
(d) none of the above
Answer: c

50. Slip ring motor is recommended where
(a) speed control is required
(6) frequent starting, stopping and reversing is required
(c) high starting torque is needed
(d) all above features are required
Answer: d

51. As load on an induction motor goes on increasing
(a) its power factor goes on decreasing
(b) its power factor remains constant
(c) its power factor goes on increasing even after full load
(d) its power factor goes on increasing up to full load and then it falls again
Answer: d

52. If a 3-phase supply is given to the stator and rotor is short circuited rotor will move
(a) in the opposite direction as the direction of the rotating field
(b) in the same direction as the direction of the field
(c) in any direction depending upon phase squence of supply
Answer: b

53. It is advisable to avoid line starting of induction motor and use starter because
(a) it will run in reverse direction
(b) it will pick up very high speed and may go out of step
(c) motor takes five to seven times its full load current
(d) starting torque is very high
Answer: c

54. The speed characteristics of an induction motor closely resemble the speedload characteristics of which of the
following machines
(a) D.C. series motor
(b) D.C. shunt motor
(c) universal motor
(d) none of the above
Answer: b

55. Which type of bearing is provided in small induction motors to support the rotor shaft ?
(a) Ball bearings
(b) Cast iron bearings
(c) Bush bearings
(d) None of the above
Answer: a

56. A pump induction motor is switched on to a supply 30% lower than its rated voltage. The pump runs. What will
eventually happen ? It will
(a) stall after sometime
(b) stall immediately
(c) continue to run at lower speed without damage
(d) get heated and subsequently get damaged
Answer: d

57. 5 H.P., 50-Hz, 3-phase, 440 V, induction motors are available for the following r.p.m. Which motor will be the
costliest ?
(a) 730 r.p.m.
(b) 960 r.p.m.
(c) 1440 r.p.m.
(d) 2880 r.p.m.
Answer: a

58. A 3-phase slip ring motor has
(a) double cage rotor
(6) wound rotor
(c) short-circuited rotor
(d) any of the above
Answer: b

59. The starting torque of a 3-phase squirrel cage induction motor is
(a) twice the full load torque
(b) 1.5 times the full load torque
(c) equal to full load torque
Answer: b

60. Short-circuit test on an induction motor cannot be used to determine
(a) windage losses
(b) copper losses
(c) transformation ratio
(d) power scale of circle diagram
Answer: a

61. In a three-phase induction motor
(a) iron losses in stator will be negligible as compared to that in rotor
(6) iron losses in motor will be neg¬ligible as compared to that in rotor
(c) iron losses in stator will be less than that in rotor
(d) iron losses in stator will be more than that in rotor
Answer: d

62. In case of 3-phase induction motors, plugging means
(a) pulling the motor directly on line without a starter
(b) locking of rotor due to harmonics
(c) starting the motor on load which is more than the rated load
(d) interchanging two supply phases for quick stopping
Answer: d

63. Which is of the following data is required to draw the circle diagram for an induction motor ?
(a) Block rotor test only
(b) No load test only
(c) Block rotor test and no-load test
(d) Block rotor test, no-load test and stator resistance test
Answer: d

64. In three-phase induction motors sometimes copper bars are placed deep in the rotor to
(a) improve starting torque
(b) reduce copper losses
(c) improve efficiency
(d) improve power factor
Answer: a

65. In a three-phase induction motor
(a) power factor at starting is high as compared to that while running
(b) power factor at starting is low as compared to that while running
(c) power factor at starting in the same as that while running
Answer: b

66. The vafcie of transformation ratio of an induction motor can be found by
(a) open-circuit test only
(b) short-circuit test only
(c) stator resistance test
(d) none of the above
Answer: b

67. The power scale of circle diagram of an induction motor can be found from
(a) stator resistance test
(6) no-load test only
(c) short-circuit test only
(d) noue of the above
Answer: c

68. The shape of the torque/slip curve of induction motor is
(a) parabola
(b) hyperbola
(c) rectangular parabola
(d) straigth line
Answer: c

69. A change of 4% of supply voltage to an induction motor will produce a change of appromimately
(a) 4% in the rotor torque
(b) 8% in the rotor torque
(c) 12% in the rotor torque
(d) 16% in the rotor torque
Answer: d

70. The stating torque of the slip ring induction motor can be increased by adding
(a) external inductance to the rotor
(b) external resistance to the rotor
(c) external capacitance to the rotor
(d) both resistance and inductance to rotor
Answer: b

71. A 500 kW, 3-phase, 440 volts, 50 Hz, A.C. induction motor has a speed of 960 r.p.m. on full load. The machine has 6 poles. The slip of the machine will be
(a) 0.01
(b) 0.02
(c) 0.03
(d) 0.04
Answer: d

72. The complete circle diagram of induetion motor can be drawn with the help of data found from
(a) noload test
(6) blocked rotor test
(c) stator resistance test
(d) all of the above
Answer: d

73. In the squirrel-cage induction motor the rotor slots are usually given slight skew
(a) to reduce the magnetic hum and locking tendency of the rotor
(b) to increase the tensile strength of the rotor bars
(c) to ensure easy fabrication
(d) none of the above
Answer: a

74. The torque of a rotor in an induction motor under running condition is maximum
(a) at the unit value of slip
(b) at the zero value of slip
(c) at the value of the slip which makes rotor reactance per phase equal to the resistance per phase
(d) at the value of the slip which makes the rotor reactance half of the rotor
Answer: c

75. What will happen if the relative speed between the rotating flux of stator and rotor of the induction motor is zero ?
(a) The slip of the motor will be 5%
(b) The rotor will not run
(c) The rotor will run at very high speed
(d) The torque produced will be very large
Answer: b

76. The circle diagram for an induction motor cannot be used to determine
(a) efficiency
(b) power factor
(c) frequency
(d) output
Answer: a

77. Blocked rotor test on induction motors is used to find out
(a) leakage reactance
(b) power factor on short circuit
(c) short-circuit current under rated voltage
(d) all of the above
Answer: d

78. Lubricant used for ball bearing is usually
(a) graphite
(b) grease
(c) mineral oil
(d) molasses
Answer: b

79. An induction motor can run at synchronous speed when
(a) it is run on load
(b) it is run in reverse direction
(c) it is run on voltage higher than the rated voltage
(d) e.m.f. is injected in the rotor circuit
Answer: d

80. Which motor is preferred for use in mines where explosive gases exist ?
(a) Air motor
(b) Induction motor
(c) D.C. shunt motor
(d) Synchronous motor
Answer: a

81. The torque developed by a 3-phase induction motor least depends on
(a) rotor current
(b) rotor power factor
(c) rotor e.m.f.
(d) shaft diameter
Answer: d

82. In an induction motor if air-gap is increased
(a) the power factor will be low
(b) windage losses will be more
(c) bearing friction will reduce
(d) copper loss will reduce In an induction motor
Answer: a

83. In induction motor, percentage slip depends on
(a) supply frequency
(b) supply voltage
(c) copper losses in motor
(d) none of the above
Answer: c

84. When /?2 is the rotor resistance, .X2 the rotor reactance at supply frequency and s the slip, then the condition for maximum torque under running conditions will be
(a) sR2X2 = 1
(b) sR2 = X2
(c) R2 = sX2
(d) R2 = s2X2
Answer: c

85. In case of a double cage induction motor, the inner cage has
(a) high inductance arid low resistance
(b) low inductance and high resistance
(c) low inductance and low resistance
(d) high inductance and high resistance
Answer: a

86. The low power factor of induction motor is due to
(a) rotor leakage reactance
(b) stator reactance
(c) the reactive lagging magnetizing current necessary to generate the magnetic flux
(d) all of the above
Answer: d

87. Insertion of reactance in the rotor circuit
(a) reduces starting torque as well as maximum torque
(b) increases starting torque as well as maximum torque
(c) increases starting torque but maxi-mum torque remains unchanged
(d) increases starting torque but maxi-mum torque decreases
Answer: a

88. Insertion of resistance in the rotcir of an induction motor to develop a given torque
(a) decreases the rotor current
(b) increases the rotor current
(c) rotor current becomes zero
(d) rotor current rernains same
Answer: d

89. For driving high inertia loods best type of induction motor suggested is
(a) slip ring type
(b) squirrel cage type
(c) any of the above
(d) none of the above
Answer: a

90. Temperature of the stator winding of a three phase induction motor is obtained by
(a) resistance rise method
(b) thermometer method
(c) embedded temperature method
(d) all above methods
Answer: d

91. The purpose of using short-circuit gear is
(a) to short circuit the rotor at slip rings
(b) to short circuit the starting resistances in the starter
(c) to short circuit the stator phase of motor to form star
(d) none of the above
Answer: a

92. In a squirrel cage motor the induced e.m.f. is
(a) dependent on the shaft loading
(b) dependent on the number of slots
(c) slip times the stand still e.m.f. induced in the rotor
(d) none of the above
Answer: c

93. Less maintenance troubles are experienced in case of
(a) slip ring induction motor
(6) squirrel cage induction motor
(c) both (a) and (b)
(d) none of the above
Answer: b

94. A squirrel cage induction motor is not selected when
(a) initial cost is the main consideration
(b) maintenance cost is to be kept low
(c) higher starting torque is the main consideration
(d) all above considerations are involved
Answer: c

95. Reduced voltage starter can be used with
(a) slip ring motor only but not with squirrel cage induction motor
(b) squirrel cage induction motor only but not with slip ring motor
(c) squirrel cage as well as slip ring induction motor
(d) none of the above
Answer: c

96. Slip ring motor is preferred over squirrel cage induction motor where
(a) high starting torque is required
(b) load torque is heavy
(c) heavy pull out torque is required
(d) all of the above
Answer: a

97. In a star-delta starter of an induction motor
(a) resistance is inserted in the stator
(b) reduced voltage is applied to the stator
(c) resistance is inserted in the rotor
(d) applied voltage perl stator phase is 57.7% of the line voltage
Answer: d

98. The torque of an induction motor is
(a) directly proportional to slip
(b) inversely proportional to slip
(c) proportional to the square of the slip
(d) none of the above
Answer: a

99. The rotor of an induction motor runs at
(a) synchronous speed
(b) below synchronous speed
(c) above synchronous speed
(d) any of the above
Answer: b

100. The starting torque of a three phase induction motor can be increased by
(a) increasing slip
(b) increasing current
(c) both (a) and (b)
(d) none of the above
Answer: c

110. Insertion of resistance in the stater of an induction motor
(a) increases the load torque
(b) decreases the starting torque
(c) increases the starting torque
(d) none of the above
Answer: b

Polyphase Induction Motors Objective Questions with Answers Pdf Download