## 300+ TOP Network Analysis Interview Questions and Answers

Q1. How A Band Pass Filter Is Constructed?

This filter is a combination of two parallel tuned circuits. This is a special type of LC filter along with a particular BW frequency to be allowed through it.

Q2. Define Branch?

It is a part of a network which lies between two junction points.

Q3. What Are The Materials Used For Resistor?

The materials used are:

Manganin (alloy of copper, manganese and nickel. Copper86%, Manganese 12%, and Nickel 2%) Constantan (alloy of nickel and copper. Copper 55% and Nickel 45%).

Q4. What Happens To Voltage When Current Is Zero?

The voltage is constant.

Q5. State Thevenin Theorem?

This theorem states that any linear network with output terminal AB can be replaced by a single voltage source V in series with a single impedance.

Q6. Define Cut-off Frequency?

The frequency that separates the pass and attenuation band is known as cut-off frequency.

Q7. What Are The Properties Of A Resistor?

The properties are high resistivity, resistance to oxidation, corrosion and moisture.

Q8. List The Characteristics Of Filter?

An ideal filter would trmit signals under the pass-band frequencies without attenuation and completely suppress the signal with attenuation band of frequencies with a sharp cut-off profile.

Q9. State Superposition Theorem?

If a number of voltages or current sources are acting simultaneously in a linear network the resultant current in any branch is the algebraic sum of current that would be produced in it when each source acts alone replacing all other independent sources by their internal resistances.

Q10. Which Capacitor Is Preferred For High Voltage And Frequency?

The vacuum and gas filled capacitor are used for high voltage and frequency applications.

Q11. Define Active Filter?

The active filter contains components like operational amplifier that introduce some gain in the signal.

Q12. What Is The Material Used For Inductance Coil?

The material used is marble because it is unaffected by atmospheric conditions.

Q13. Define Norton Equivalent Circuit?

The Norton equivalent circuit is a current generator which is placed in parallel to internal resistance.

Q14. Is The Theorem Applicable To A.c. Sources?

No, it is applicable to dc circuits with and without controlled sources.

Q15. What Is The Efficiency During Maximum Power Trfer?

Efficiency during maximum power trfer 50%.

Q16. Define Filter?

A filter is an electrical network that can trmit signals within a specified frequency range.

Q17. List The Disadvantages Of Constant K Filters?

The attenuation does not increase rapidly beyond cut-off frequency. Characteristics impedance varies widely in the pass band from desired value.

Q18. Define Unilateral Circuit?

The circuit whose properties are not same in either direction is known as unilateral circuit.

Q19. List Advantages Of Active Filter Over Passive Filter?

Active filter eliminate bulky components. It offers gain. It can drive low impedance loads. It is easy to tune

Q20. List Examples Of Voltage Source?

The examples of voltage source are battery and generator.

Q21. What Are The Applications Of Filter?

The Filter is used in voice frequency telegraphy, multi channel communication, TV broadcasting and telephony.

Q22. What Is Q Factor?

The Q factor is ratio of inductive reactance to resistance of a coil.

Q23. What Is Inductance?

It is the property of a material by virtue of which it opposes any change of magnitude and direction of current passing through the conductor.

Q24. What Is Resistance?

The resistance is the property of a material to oppose the flow of current in a material. Its unit is ohm.

Q25. What Is The Unit Of Charge And Current?

The units are coulomb and ampere.

Q26. How Equivalent Impedance Is Calculated In Thevenin Theorem?

All independent voltage sources are short circuited and all independent current sources are open circuited.

Q27. State Maximum Power Trfer Theorem?

A resistance load being connected to a dc network receives maximum power when load resistance is equal to internal resistance.

Q28. What Happens To Voltage When Current Through The Inductor Is Constant?

The voltage across inductor is zero.

Q29. What Are Dependent Sources?

When strength of voltage or current changes in the source for any change in the connected network they are called dependent sources.

Q30. What Is The Unit Of Attenuation?

The unit is decibel and neper.

Q31. Define Characteristics Impedance?

The characteristics impedance of a filter matches with circuit to which it is connected throughout the pass band.

Q32. When We Use 3-terminal Resistor?

It is used when resistance is less than 1 ohm.

Q33. List Examples Of Current Sources?

Semiconductor devices like tristor and diode are treated as current sources.

Q34. How Will You Define Capacitance?

It is the ability to store electric charge within it. Capacitance is a measure of charge per unit voltage that can be stored in an element.

Q35. Define Active And Passive Network?

• Active network: The network which has no current or voltage source is called passive network.
• Passive network: The network which either has current or voltage source is called active network.