250+ TOP MCQs on DC Imperfections in Operational Amplifiers and Answers

Posted on by engineerComments Off on 250+ TOP MCQs on DC Imperfections in Operational Amplifiers and Answers

Electronic Devices and Circuits Quiz on “DC Imperfections in Operational Amplifiers”.

Can be stored for long periods of time and it’s easy to carry. Hace buy tarceva canada Sant Quirze del Vallès ya más de 2 meses que necesito la carga cytotec pero todavía no he hecho nada para conseguirlo por el tiempo que tarda en llegar. In cases of bacterial infections that affect the bloodstream, amoxicillin may be used to prevent bacterial infection by treating an infection before it can get any worse.

Trimix is indicated for treating moderate or severe gout, especially if accompanied. It was found that in developed countries, breast cancer is second only to lung cancer in incidence and is the most common cause of cancer deaths in both sexes buy provigil online europe Ciudad Fernández in women. It is an antidepressant that has been prescribed for years to improve the symptoms of adhd.

1. Consider an inverting amplifier with a nominal gain of 1000 constructed from an op amp with an input offset voltage of 3 mV and with output saturation levels of ±10 V. What is (approximately) the peak sine-wave input signal that can be applied without output clipping?
A. 7 mV
B. 10 mV
C. 13 mV
D. 9mV

Answer: A
Clarification: The maximum that can be sent without clipping is 10V – 1000 X 3mV or 7V.

(Q2 & Q.3) Consider an inverting amplifier with a nominal gain of 1000 constructed from an op amp with an input offset voltage of 3 mV and with output saturation levels of ±10 V. If the effect of VOs(input offset voltage) is nulled at room temperature (250C., how large an input can one now apply if:

2. The circuit is to operate at a constant temperature?
A. 8.5 mV
B. 9 mV
C. 9.5 mV
D. 10 mV

Answer: D
Clarification: Clarification: Maximum signal that will not be clipped is 10mV because 10mV X 1000 = 10V.

3. The circuit is to operate at a temperature in the range 0°C to 75°C and the temperature coefficient of VOS is 10 μV/°C?
A. 8.5 mV
B. 9 mV
C. 9.5 mV
D. 10 mV

Answer: C
Clarification: Since the effect is nullified at 25oC. the peak that can be sent now is given by 10 – (75-25) X 0.1 mV.

4. One of the DC imperfections of the amplifiers are dc offset voltage which is
A. Existence of output signal even when the common mode signal is zero
B. Existence of common mode signal causing zero output signal
C. Existence of output signal even when the differential signal is zero
D. Existence of differential signal causing zero output signal

Answer: C
Clarification: DC offset voltage is existence of output signal even when the differential signal is zero.

5. For the amplifier shown determine the value of the bias current (Ib) and input offset current (Io) respectively.

A. Ib = IB1 + IB2 Io = IB1 – IB2
B. Ib = IB1 + IB2 Io = | IB1 – IB2 |
C. Ib = 0.5(IB1 + IB2) Io = | IB1 – IB2 |
D. Ib = 0.5(IB1 + IB2) Io = IB1 – IB2

Answer: C
Clarification: Standard mathematical expressions are used with the given variables.

6. Consider the circuit shown below which reduces the impact of the input bias current. If IB1 = IB2 = Input bias current, then determine the value of R3 so that the output voltage (v0) is not impacted by the input bias current.

A. (R1 R2)/(R1+R2)
B. (R1 R2)/(R1-R2)
C. R1-(R1 R2)/(R1+R2)
D. R2- (R1 R2)/(R1+R2)

Answer: A
Clarification: This will be possible when R3 has the same value as the net effect of R1 and R2.

7. Consider an inverting amplifier circuit designed using an op amp and two resistors, R1 = 10 kΩ and R2 = 1 MΩ. If the op amp is specified to have an input bias current of 100 nA and an input offset current of 10 nA, find the output dc offset voltage resulting.
A. 0.1 mV
B. 1 mV
C. 10 mV
D. 100 mV

Answer: D
Clarification: Use the mathematical definition of bias current and offset current.

(Q.8-Q.10) Consider a Miller integrator with a time constant of 1ms and an input resistance of 10 kΩ. Let the op amp have VOS (offset voltage) = 2 mV and output saturation voltages of ±12 V.

8. Assuming that when the power supply is turned on the capacitor voltage is zero, how long does it take for the amplifier to saturate?
A. 3s
B. 6s
C. 9s
D. 12s

Answer: B
Clarification: Use vO = VOS
(VOS/CR)t.

9. Select the largest possible value for a feedback resistor RF so that at least ±10 V of output signal swing remains available.
A. 10 kΩ
B. 100 kΩ
C. 1 MΩ
D. 10 MΩ

Answer: D
Clarification: Use vO = VOS
(VOS/CR)t.

10. What is the corner frequency of the resulting STC network?
A. 1 Hz
B. 0.16 Hz
C. 0.33 Hz
D. 0.5 Hz

Answer: B
Clarification: The required answer is given by 1/6 Hz.