# 300 TOP MOST NETWORK THEOREMS – Electrical Engineering Multiple choice Questions and Answers

## NETWORK THEOREMS Multiple choice Questions :-

1. Kirchhoff s current law states that
(a) net current flow at the junction is positive
(b) Hebraic sum of the currents meeting at the junction is zero
(c) no current can leave the junction without some current entering it.
(d) total sum of currents meeting at the junction is zero
Ans: b

2. According to Kirchhoffs voltage law, the algebraic sum of all IR drops and e.m.fs. in any closed loop of a network is always
(a) negative
(b) positive
(c) determined by battery e.m.fs.
(d) zero
Ans: d

3. Kirchhoffs current law is applicable to only
(a) junction in a network
(b) closed loops in a network
(c) electric circuits
(d) electronic circuits
Ans: a

4. Kirchhoffs voltage law is related to
(a) junction currents
(b) battery e.m.fs.
(c) IR drops
(d) both (b) and (c)
(e) none of the above
Ans: d

5. Superposition theorem can be applied only to circuits having
(a) resistive elements
(b) passive elements
(c) non-linear elements
(d) linear bilateral elements
Ans: d

6. The concept on which Superposition theorem is based is
(a) reciprocity
(b) duality
(c) non-linearity
(d) linearity
Ans: d

7. Thevenin resistance Rth is found
(a) by removing voltage sources along with their internal resistances
(6) by short-circuiting the given two terminals
(c) between any two ‘open’ terminals
(d) between same open terminals as for Etk
Ans: d

8. An ideal voltage source should have
(a) large value of e.m.f.
(b) small value of e.m.f.
(c) zero source resistance
(d) infinite source resistance
Ans: c

9. For a voltage source
(a) terminal voltage is always lower than source e.m.f.
(b) terminal voltage cannot be higher than source e.m.f.
(c) the source e.m.f. and terminal voltage are equal
Ans: b

10. To determine the polarity of the voltage drop across a resistor, it is necessary to know
(a) value of current through the resistor
(b) direction of current through the resistor
(c) value of resistor
(d) e.m.fs. in the circuit
Ans: b

11. “Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load”. The above statement is associated with
(a) Millman’s theorem
(b) Thevenin’s theorem
(c) Superposition theorem
(d) Maximum power transfer theorem
Ans: d

12. “Any number of current sources in parallel may be replaced by a single current source whose current is the algebraic sum of individual source currents and source resistance is the parallel combination of individual
source resistances”.
The above statement is associated with
(a) Thevenin’s theorem
(b) Millman’s theorem
(c) Maximum power transfer theorem
(d) None of the above
Ans: b

13. “In any linear bilateral network, if a source of e.m.f. E in any branch produces a current I in any other branch, then same e.m.f. acting in the second branch would produce the same current / in the first branch”.
The above statement is associated with
(a) compensation theorem
(b) superposition theorem
(c) reciprocity theorem
(d) none of the above
Ans: c

14. Which of the following is non-linear circuit parameter ?
(a) Inductance
(b) Condenser
(c) Wire wound resistor
(d) Transistor
Ans: a

15. A capacitor is generally a
(a) bilateral and active component
(b) active, passive, linear and nonlinear component
(c) linear and bilateral component
(d) non-linear and active component
Ans: c

16. “In any network containing more than one sources of e.m.f. the current in any branch is the algebraic sum of a number of individual fictitious currents (the number being equal to the number of sources of e.m.f.), each of which is due to separate action of each source of e.m.f., taken in order, when the remaining sources of e.m.f. are replaced by conductors, the resistances of which are equal to the internal resistances of the respective sources”.
The above statement is associated with
(a) Thevenin’s theorem
(b) Norton’s theorem
(c) Superposition theorem
(d) None of the above
Ans: c

17. Kirchhoff s law is applicable to
(a) passive networks only
(b) a.c. circuits only
(c) d.c. circuits only
(d) both a.c. as well d.c. circuits
Ans: d

18. Kirchhoff s law is not applicable to circuits with
(a) lumped parameters
(b) passive elements
(c) distributed parameters
(d) non-linear resistances
Ans: c

19. Kirchhoff s voltage law applies to circuits with
(a) nonlinear elements only
(b) linear elements only
(c) linear, non-linear, active and passive elements
(d) linear, non-linear, active, passive, time varying as wells as time-in-variant elements
Ans: d

20. The resistance LM will be
(a) 6.66 Q
(b) 12 Q
(c) 18Q
(d) 20Q
Ans: a

21. For high efficiency of transfer of power, internal resistance of the source should be
(a) equal to the load resistance
(b) less than the load resistance
(c) more than the load resistance
(d) none of the above
Ans: b

22. Efficiency of power transfer when maximum transfer of power c xerosis
(a) 100%
(b) 80%
(c) 75%
(d) 50%
Ans: d

23. If resistance across LM in Fig. 2.30 is 15 ohms, the value of R is
(a) 10 Q
(6) 20 Q
(c) 30 Q
(d) 40 Q
Ans: c

24. For maximum transfer of power, internal resistance of the source should be
(b) less than the load resistance
(c) greater than the load resistance
(d) none of the above
Ans: a

25. If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be
(a) a voltage source
(b) a current source
(c) both of above
(d) none of the above
Ans: a

26. The circuit whose properties are same in either direction is known as
(a) unilateral circuit
(b) bilateral circuit
(c) irreversible circuit
(d) reversible circuit
Ans: b

27. In a series parallel circuit, any two resistances in the same current path must be in
(a) series with each other
(b) parallel with each other
(c) series with the voltage source.’
(d) parallel with the voltage source
Ans: a

28. The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as
(a) non-linear circuit
(b) linear circuit
(c) bilateral circuit
(d) none of the above
Ans: a

29. A non-linear network does not satisfy
(a) superposition condition
(b) homogeneity condition
(c) both homogeneity as well as superposition condition
(d) homogeneity, superposition and associative condition
Ans: c

30. An ideal voltage source has
(a) zero internal resistance
(b) open circuit voltage equal to the voltage on full load
(c) terminal voltage in proportion to current
(d) terminal voltage in proportion to load
Ans: a

31. A network which contains one or more than one source of e.m.f. is known as
(a) linear network
(b) non-linear network
(c) passive network
(d) active network
Ans: c

32. The superposition theorem is applicable to
(a) linear, non-linear and time variant responses
(b) linear and non-linear resistors only
(c) linear responses only
(d) none of the above
Ans: c

33. Which of the following is not a nonlinear element ?
(a) Gas diode
(b) Heater coil
(c) Tunnel diode
(d) Electric arc
Ans:

34. Application of Norton’s theorem to a circuit yields
(a) equivalent current source and impedance in series
(6) equivalent current source and impedance in parallel
(c) equivalent impedance
(d) equivalent current source
Ans: a

35. Millman’s theorem yields
(a) equivalent resistance
(6) equivalent impedance
(c) equivalent voltage source
(d) equivalent voltage or current source
Ans: d

36. The superposition theorem is applicable to
(a) voltage only
(b) current “only
(c) both current and voltage
(d) current voltage and power
Ans: d

37. Between the branch voltages of a loop the Kirchhoff s voltage law imposes
(a) non-linear constraints
(b) linear constraints
(c) no constraints
(d) none of the above
Ans: b

38. A passive network is one which contains
(a) only variable resistances
(b) only some sources of e.m.f. in it
(c) only two sources of e.m.f. in it
(d) no source of e.m.f. in it
Ans: d

39. A terminal where three on more branches meet is known as
(a) node
(b) terminus
(c) combination
(d) anode
Ans: a

40. Which of the following is the passive element ?
(a) Capacitance
(b) Ideal current source
(c) Ideal voltage source
(d) All of the above
Ans: a

41. Which of the following is a bilateral element ?
(a) Constant current source
(b) Constant voltage source
(c) Capacitance
(d) None of the above
Ans: c

42. A closed path made by several branches of the network is known as
(a) branch
(b) loop
(c) circuit
(d) junction
Ans: b

43. A linear resistor having 0 < R < °o is a
(a) current controlled resistor
(6) voltage controlled resistor
(c) both current controlled and voltage controlled resistor
(d) none of the above
Ans: c

44. A star circuit has element of resistance R/2. The equivalent delta elements will be
(a) R/6
(b) fi?
(c) 2R
(d) 4R
Ans: b

45. A delta circuit has each element of value R/2. The equivalent elements of star circuit with be
(a) RIG
(b) R/3
(c) 2R
(d) 3R
Ans: a

56. In Thevenin’s theorem, to find Z
(a) all independent current sources are short circuited and independent voltage sources are open circuited
(b) all independent voltage sources are open circuited and all independent current sources are short circuited
(c) all independent voltage and current sources are short circuited
(d) all independent voltage sources are short circuited and all independent current sources are open circuited
Ans: d

57. While calculating Rth in Thevenin’s theorem and Norton equivalent
Ans: a

58. The number of independent equations to solve a network is equal to
(a) the number of chords
(b) the number of branches
(c) sum of the number of branches and chords
(d) sum of number of branches, chords and nodes
Ans: a

59. The superposition theorem requires as many circuits to be solved as there are
(a) sources, nodes and meshes
(b) sources and nodes
(c) sources
(d) nodes
Ans: c

60. Choose the incorrect statement.
(a) A branch formed by the parallel connection of any resistor R and open circuit has the characteristic of an open circuit.
(b) A branch formed by the parallel connection of any resistor R and a short circuit has the characteristic of a short circuit.
(c) A branch formed by the series connection of any resistor R and an open circuit has the characteristic of an open circuit.
(d) A branch formed by the series connection of any resistor R and a short circuit has the characteristic of resistor R.
Ans: a

#### 39 thoughts on “300 TOP MOST NETWORK THEOREMS – Electrical Engineering Multiple choice Questions and Answers”

1. Raghunath Munda says:

Sir I need explanation so that I can understand details ……….and easy .For this I think it is too important for who all needed a help of u…….

2. Raghunath Munda says:

Sir for this to me is very important to me and I can face problems ……..I think and is very necessary for who all r feeding ……I think he/she can improve lots of…………….send me ………….

3. basavraj says:

Q14……answer will be transistor i.e D

4. Dhirendra Pratap says:

33- b answer heater coil because it is linear element

5. Abdul Waha Khan says:

hi gyes ,,,
anyone please send me copy of this at
iam_abdulwahab001@yahoo.com

6. Raghav says:

I am preparing for MAHAGENCO exam 2017 , please send me the material required for the exam at raghavgothe@gmail.com

7. praveen says:

Q-45 ans is R/6

8. Shabina says:

Plz provide me with a pdf copy of all the q a ans.. …..

9. Arvind.Suryawanshi says:

Q34.:- B
voltage and current sources can be replaced by an equivalent circuit consisting of an equivalent current source in parallel connection with an equivalent resistance.

1. basavraj says:

correct..arvind

10. neha says:

14- a/d???? plz check

1. Arvind.Suryawanshi says:

Hi..
@neha
examples of nonlinear elements are transistors and other semiconductor devices, vacuum tubes, and iron core inductors and transformers when operated above their saturation current.
Examples of linear elements are resistors, capacitors, and air core inductors.

11. Dheerendra Kumar says:

Sir plz send me soft copy At strongwill28@gmail.com

12. SATHI says:

13. Bhasker says:

34 is B.
Norton’s current is parallel with Norton ‘s resistance

14. RAJU S MULEY says:

PLEASE SEND ME THESE PDF FILES

15. DIVYASHREE S says:

pls send me all electrical engineering mcq its very helpfull for us ,send to sdivyashree.s@gmail.com

16. Jj says:

17. Mohammad.parvez 46@ says:

Send me pdf files

18. Mohammad.parvez says:

Plz send me pdf file

19. RITHIKA C says:

sir please send me the soft copy to rithikac6@gmail.com

20. Mohit says:

21. Ritupon says:

Plz send me the mcq of electrical and electronic to my mail id.. dhunritugogoi06@gmai.com

22. mahadu b mahala says:

please sent me all question on my email id tejasmahala2003@yahoo.com

23. pardeep kumar says:

question 31 ans is D

24. naik says:

25. Shobhit says:

Please share interview based questions on superposition theoram

26. kumar says:

Q 33 ans is B…

HOW CAN U DEFINE LINEAR & NON-LINEAR CIRCUIT OR ELEMENT….?//

ANS:: THE CURRENT WAVE FORM IS IMMEDIATELY FOLLOWED BY VOLTAGE MEANS ITS A LINEAR…
IF THE THERE IS A DELAY MEANS WHICH IS A NON – LINEAR, EX DIODE, TRANSISTOR, SCR ETC ETC…
SOME POTENTIAL REQUIRED TO SWITCH THE DEVICE, SO THE CURRENT IS NOT IMMEDIATELY FOLLOWING THE VOLTAGE…..

AS I LEARNT FROM TANGEDCO R&D….

27. Nataraj says:

Please share d soft copy to natarajb307@gmail.com

28. Nataraj says:

it will be great help if someone please share the soft copy to natarajb307@gmail.com

29. Neha says:

Q.44 ans will be 3R/2

1. swapnil says:

right neha

30. Anand says:

Sir I need all the MCQs of Electrical and Electronics Engineering,Please send me on anandmshr45@gmail.com

31. saurav says:

i want exlanation for all question then we understand easily……………………………sir please provide disscusion on this website………………………………………………………………………………………………………………………….

32. neeraj says:

I think… Sir

Que nu 31 ans should be d

Que nu 36 ans should be c

Plz sir recheck these ans

1. Asha says:

U r ryt…. N 33 ans is B

33. rakesh says:

Sir kindly give some easy question and answer which we may face interview

1. Nataraj says:

Please share the soft copy to my id – natarajb307@gmail.com

34. vijay says:

send the soft copy