500+ TOP Engineering Physics MCQs and Answers Quiz

Engineering Physics Multiple Choice Questions

1. Which law is also called as the elasticity law?
A. bernoulli’s law
B. stress law
C. hooke’s law
D. poisson’s law

Answer: C hooke’s law
Explanation: the hooke”s law is valid under the elastic limit of a body. it itself states that stress is proportional to the strain within the elastic limit.

2. The materials which have the same elastic properties in all directions are called
A. isotropic
B. brittle
C. homogeneous
D. hard

Answer: A isotropic
Explanation: same elastic properties in all direction is called the homogenity of a material.

3. A member which does not regain its original shape after removal of the load producing deformation is said
A. plastic
B. elastic
C. rigid
D. none of the mentioned

Answer: A plastic
Explanation: a plastic material does not

4. The property by which a body returns to its original shape after removal of the force is called
A. plasticity
B. elasticity
C. ductility
D. malleability

Answer: B elasticity
Explanation: when an external force acts on a body, the body tends to undergo some deformation. if the external force is removed and the body comes back to its original shape and size, the body is known as elastic body and this property is called elasticity.

5. The property of a material by which it can be beaten or rolled into thin plates is called
A. malleability
B. plasticity
C. ductility
D. elasticity

Answer: A malleability
Explanation: a material can be beaten into thin plates by its property of malleability.

6. The body will regain it is previous shape and size only when the deformation caused by the external forces, is within a certain limit. What is that limit?
A. plastic limit
B. elastic limit
C. deformation limit
D. none of the mentioned

Answer: B elastic limit
Explanation: the body only regain its previous shape and size only upto its elastic limit.

7. The materials which have the same elastic properties in all directions are called
A. isotropic
B. brittle
C. homogenous
D. hard

Answer: A isotropic
Explanation: isotropic materials have the same elastic properties in all directions.

8. As the elastic limit reaches, tensile strain
A. increases more rapidly
B. decreases more rapidly
C. increases in proportion to the stress
D. decreases in proportion to the stress

Answer: A increases more rapidly
Explanation: on reaching the tensile stress to the elastic limit after the proportionality limit, the stress is no longer proportional to the strain. then the value of strain rapidly increases.

9. What kind of elastic materials are derived from a strain energy density function?
A. cauchy elastic materials
B. hypo elastic materials
C. hyper elastic materials
D. none of the mentioned

Answer: C hyper elastic materials
Explanation: the hyper elastic materials are derived from a strain energy density function. a model is hyper elastic if and only if it is possible to express the cauchy stress tensor as a function of the deformation gradient.

10. What the number that measures an object’s resistance to being deformed elastically when stress is applied to it?
A. elastic modulus
B. plastic modulus
C. poisson’s ratio
D. stress modulus

Answer: A elastic modulus
Explanation: the elastic modulus is the ratio of stress to strain.

Engineering Physics MCQs

11. The slope of the stress-strain curve in the elastic deformation region is
A. elastic modulus
B. plastic modulus
C. poisson’s ratio
D. none of the mentioned

Answer: A elastic modulus
Explanation: the elastic modulus is the ratio of stress and strain. so on the stress strain curve, it is the slope.

12. What is the stress-strain curve?
A. it is the percentage of stress and stain
B. it is the relationship between stress and strain
C. it is the difference between stress and strain
D. none of the mentioned

Answer: B it is the relationship between stress and strain
Explanation: the relationship between stress

13. Which point on the stress strain curve occurs after the proportionality limit?
A. upper yield point
B. lower yield point
C. elastic limit
D. ultimate point

Answer: C elastic limit
Explanation: the curve will be stress strain proportional upto the proportionality limit. after these, the elastic limit will occur.

14. Which point on the stress strain curve occurs after the lower yield point?
A. yield plateau
B. upper yield point
C. ultimate point
D. none of the mentioned

Answer: A yield plateau
Explanation: the points on the curve comes in the given order,

15. Which point on the stress strain curve occurs after yield plateau?
A. lower yield point
B. upper yield point
C. ultimate point
D. breaking point

Answer: C ultimate point
Explanation: after the yield plateau the curve will go up to its maximum limit of stress which is its ultimate point.

16. Which point on the stress strain curve occurs after the ultimate point?
A. last point
B. breaking point
C. elastic limit
D. material limit

Answer: B breaking point
Explanation: after the ultimate point the value of stress will reduce on increasing of strain and ultimately the material will break.

17. Elastic limit is the point
A. up to which stress is proportional to strain
B. at which elongation takes place without application of additional load
C. up to which if the load is removed, original volume and shapes are regained
D. none of the mentioned

Answer: C up to which if the load is removed, original volume and shapes are regained
Explanation: the elastic limit is that limit up to which any material behaves like an elastic material.

18. What is the point P shown on the stress strain curve?
A. upper yield point
B. yield plateau
C. elastic limit
D. ultimate point

Answer: D ultimate point
Explanation: it is the point showing the maximum stress to which the material can be subjected in a simple tensile stress.

19. What is the point P shown in the stress- strain curve?
A. lower yield point
B. elastic limit
C. proportionality limit
D. breaking point

Answer: D breaking point
Explanation: the breaking point is the point where the material breaks. the breaking point will be the last point on the stress strain curve.

20. What is the point shown in the stress strain curve?
A. elastic limit
B. lower yield point
C. yield plateau
D. lower strain point

Answer: B lower yield point
Explanation: it is the lower yield point at which the curve levels off and plastic deformation begins.

21. Where is the necking region?
A. the area between lower yield point and upper yield point
B. the area between the plastic limit and elastic limit
C. the area between the ultimate point and initial point
D. the area between the ultimate point and rupture

Answer: D the area between the ultimate point and rupture
Explanation: necking is a tensile strain deformation which is cased in after the ultimate amount of stress occurs in the material.

22. What is the elastic modulus of steel?
A. 69-79 gpa
B. 41-45 gpa
C. 190-217 gpa
D. 330-360 gpa

Answer: C 190-217 gpa
Explanation: steel has an elastic modulus of 190-217 gpa. it has e higher than aluminum and magnesium alloys. but lower than tungsten and molybdenum alloys.

23. What is the elastic modulus of titanium alloys?
A. 150-170 gpa
B. 180-214 gpa
C. 80-130 gpa
D. 41-45 gpa

Answer: C 80-130 gpa
Explanation: titanium alloys have the elastic modulus in the range of 80 to 130 gpa. it is greater than aluminum and magnesium alloys but lesser than steel.

24. What is the order of elastic modulus for Nickel alloys, Lead alloys, Molybdenum alloys, alumina?
A. pb < mo < ni < al2o3
B. ni < pb < mo < al2o3
C. pb < ni < mo < al2o3
D. pb < ni < al2o3 < mo

Answer: C pb < ni < mo < al2o3
Explanation: lowest elastic modulus is of lead and its alloys of 14-18 gpa. ni and mo alloys have elastic modulus of 180-214 and 330-360 gpa respectively. al2o3 has highest e among the four of 415 gpa.

25. What property enhances with a decrease in E?
A. flexibility
B. stiffness
C. hardness
D. uts

Answer: A flexibility
Explanation: the lower the elastic modulus of material, the more flexible it is. bending of material becomes easier. on the other hand, stiffness decreases.

26. What is the unit of elastic modulus?
A. mohs
B. gpa
C. kg
D. n

Answer: B gpa
Explanation: elastic modulus is expressed in gpa. mohs is the unit used for hardness.

27. When applied stress is of shear type, the modulus of elasticity is known as
A. bulk modulus
B. modulus of resilience
C. shear modulus
D. stiffness

Answer: C shear modulus
Explanation: when the type of stress applied is shear, e is known as shear modulus. it is also known as modulus of rigidity. stiffness is measured in terms of e.

28. Which of the following tensile property is dimensionless?
A. tensile stress
B. elastic modulus
C. true strain
D. toughness

Answer: C true strain
Explanation: true strain is dimensionless property. tensile strength and elastic modulus are measured in mpa and gpa respectively.

29. What is a factor which controls the elastic modulus?
A. alloying
B. heat treatment
C. interatomic forces
D. cold working

Answer: C interatomic forces
Explanation: on a constant temperature and pressure, e only is function of two factors.

30. Stress should not exceed when in service.
A. yield strength
B. tensile strength
C. fracture strength
D. toughness

Answer: A yield strength
Explanation: above yield strength, material starts to deform plastically. it causes a change in dimensions and properties of a material. so material should be used below it.

31. Stress should not exceed when in mechanical working
A. yield strength
B. tensile strength
C. fracture strength
D. toughness

Answer: B tensile strength
Explanation: mechanical working process consists of plastic deformation. so it is performed above yield strength. but it is limited below tensile strength so as to avoid fracture.

32. Ductility of material is its ability to flow plastically under compressive load.
A. true
B. false

Answer: B false
Explanation: ductility is a tensile property. it is studied under tensile loading. it is the ability to plastic flow without rupture.

33. Work per unit volume of the material is a known modulus of toughness.
A. true
B. false

Answer: A true
Explanation: toughness is measured by the amount of work per unit volume of the material under static loading. work per unit volume of material is called modulus of toughness.

34. Which of the following cannot be determined using a torsion test?
A. modulus of elasticity in shear
B. torsion yield strength
C. modulus of rupture
D. young’s modulus

Answer: D young’s modulus
Explanation: modulus of elasticity in shear, torsion yield strength and modulus of rupture can all be determined by performing torsion test on material.

35. What is the use of weight head in a torsion testing equipment?
A. holding the job only
B. holding the job and applying twisting moment
C. holding the job and measuring the twisting moment
D. it is not a part of torsion testing equipment

Answer: C holding the job and measuring the twisting moment
Explanation: the main job of weight head is to hold the job and measure the twisting moment.while twisting head holds the other end of job and applies twisting moment.

36. Which of the following is used to measure how much the specimen is twisted?
A. micrometer
B. clinometer
C. troptometer
D. tropometer

Answer: C troptometer
Explanation: troptometer is an instrument which is used for measuring the angular distortion of the material. mocrometer and vernier callipers are used to measure length. tropometer measures amount of torsion for a bone.

37. Torsional stress multiplied with original cross sectional are is:
A. maximum twisting load
B. minimum twisting load
C. minimum shear load
D. yield shear load

Answer: A maximum twisting load
Explanation: torsional stress is given by the ratio of maximum twisting load and original are of cross section of the material. therefore, torsional stress multiplied with original cross sectional gives us maximum twisting load.

38. Plastic deformation can only occur in case of torsional force.
A. true
B. false
C. topic 1.4 torsional stress and deformations

Answer: B false
Explanation: the above given statement is false as plastic deformation can occur in case of tensile, compressive and torsional load after a point. after this point, the body cannot recover its original shape.

39. What is the unit of polar moment of inertia?
A. m2
B. m5
C. m3
D. m4

Answer: D m4
Explanation: polar moment of inertia denoted by j, is given by integration of radius square with respect to small area of cross-

40. Torque is moment.
A. twisting
B. shear
C. bending
D. couple

Answer: A twisting
Explanation: a cylindrical shaft is subjected to twisting moment or torque when a force is acting on the member tangentially at some radius in a plane of its cross section.

41. Shear stress on a solid bar and hollow bar is same for given dimension.
A. true
B. false

Answer: B false
Explanation: shear stress for a hollow bar and a solid bar are different dimensions as the hollow bar has two dimensions, outer and inner radius because of which calculation is different than the solid bar which has only one diameter.

42. In which of the following the angle of twist increases fast for a small amount of torque?
A. cold working condition
B. hot working condition
C. warm working condition
D. the increase is the same for cold working, hot working and warm working

Answer: B hot working condition
Explanation: when the torsion test is conducted in hot working, it is observed that for a slight change in torque on the given specimen the angle of twist increase fast as

43. Torsion is denoted by
A. r
B. q
C. t
D. n

Answer: C t
Explanation: if the moment is applied in a plane perpendicular to the longitudinal axis of the beam (or) shaft it will be subjected to torsion. torsion is represented or denoted by t.

44. The SI units for torsion is
A. n m
B. n
C. n/m
D. m

Answer: A n m
Explanation: as torsion is a product of perpendicular force and radius, the units will be n m.

45. torsion is produced when twisting couple coincides with the axis of the shaft.
A. exact
B. pure
C. nominal
D. mild

Answer: B pure
Explanation: when a member is subjected to the equal and opposite twisting moment at its ends, then the member is said to be subjected under pure torsion. pure torsion is often produced when the axis of the twisting couple coincides with the axis of the shaft.

46. Which of the following is known as Re- entrant mouthpiece?
A. external mouthpiece
B. convergent mouthpiece
C. internal mouthpiece
D. cylindrical mouthpiece

Answer: C internal mouthpiece
Explanation: according to the position, mouthpieces are classified as an external mouthpiece and internal mouthpiece. if the tube projects inside the tank, it is called an internal mouthpiece or re-entrant or borda’s

47. What is the general value for coefficient of contraction?
A. 0.64
B. 0.67
C. 0.66
D. 0.7

Answer: A 0.64
Explanation: the ratio of the area of a jet at vena contracta to the area of orifice is known as the coefficient of contraction. the value of cc varies from 0.61 to 0.69 for different orifices. generally, for sharp edged orifice the value of cc may be taken as 0. 64.

48. The Cd value for internal mouthpiece running free is
A. 0.6
B. 0.5
C. 0.7
D. 0.8

Answer: B 0.5
Explanation: the cd value for internal mouthpiece running free is 0.5.

49. is the velocity with which water reaches the notch or before it flows over it.
A. velocity of contact
B. velocity of moment
C. velocity of approach
D. velocity of head

Answer: C velocity of approach
Explanation: the velocity of approach is defined as the velocity with which water reaches the notch or weir before it flows over it. this velocity of approach creates an additional head “ha” equal to va2 / 2g and effect head over the notch is increased to h+ha.

50. Which of the following is also known as V notch?
A. trapezoidal
B. stepped
C. triangular
D. sharp edged

Answer: C triangular
Explanation: a triangular notch also called a v notch is of triangle shape with apex down. the expression of the discharge over triangular notch or weir is q = 8/15 cd (2g) 1/2 × h 5/2.

51. Calculate the discharge over rectangular Weir of 3 metres length under the head of 400mm.Use Francis formula.
A. 1.268 m3/s
B. 1.396 m3/s
C. 1.475 m3/s
D. 1.528 m3/s

Answer: B 1.396 m3/s
Explanation: francis formula for discharge q = 1.84 lh3/2.

52. converts mechanical energy into hydraulic energy.
A. dynamo
B. pump
C. turbine
D. generator

Answer: B pump
Explanation: a pump is a mechanical device which converts the mechanical energy into hydraulic energy. the hydraulic energy is in the form of pressure energy. the pumps are generally used for lifting liquid from a lower level to a higher level.

53. Torsional sectional modulus is also known as
A. polar modulus
B. sectional modulus
C. torsion modulus
D. torsional rigidity

Answer: A polar modulus
Explanation: the ratio of polar moment of inertia to radius of section is called polar modulus or torsional section modulus. its units are mm3 or m3 (in si).

54. is a measure of the strength of shaft in rotation.
A. torsional modulus
B. sectional modulus
C. polar modulus
D. torsional rigidity

Answer: C polar modulus
Explanation: the polar modulus is a measure of the strength of shaft in rotation. as the value of polar modulus increases torsional strength increases.

55. What are the units of torsional rigidity?
A. nmm2
B. n/mm
C. n-mm
D. n

Answer: A nmm2
Explanation: the product of modulus of rigidity (c) and polar moment of inertia (j) is called torsional rigidity. torsional rigidity is a torque that produces a twist of one radian in a shaft of unit length.

56. The angle of twist can be written as
A. tl/j
B. cj/tl
C. tl/cj
D. t/j

Answer: C tl/cj
Explanation: the angle of twist = tl/cj

57. The power transmitted by shaft SI system is given by
A. 2πnt/60
B. 3πnt/60
C. 2πnt/45
D. nt/60 w

Answer: A 2πnt/60
Explanation: in si system, power (p) is measured in watts (w) ; p = 2πnt/60 where t = average torque in n.m

58. Area of catchment is measured in
A. mm3
B. km2
C. km
D. mm

Answer: B km2
Explanation: catchment area can be defined as the area which contributes the surplus water present over it to the stream or river. it is an area which is responsible for maintaining flow in natural water bodies. it is expressed in square kilometres.

59. catchment area is a sum of free catchment area and intercepted catchment area.
A. total
B. additional
C. combined
D. overall

Answer: C combined
Explanation: combined catchment area is defined as the total catchment area which contributes the water in to stream or a tank. combined catchment area = free catchment area + intercepted catchment area.

60. has steep slopes and gives more run off.
A. intercepted catchment area
B. good catchment area
C. combined catchment area
D. average catchment area

Answer: B good catchment area
Explanation: good catchment area consists of hills or rocky lands with steep slopes and little vegetation. it gives more run off.

61. Trend of rainfall can be studied from
A. rainfall graphs
B. rainfall records
C. rainfall curves
D. rainfall cumulatives

Answer: B rainfall records
Explanation: rainfall records are useful for calculating run off over a basin. by using rainfall records estimate of design parameters of irrigation structures can be made. the maximum flow due to any storm can be calculated and predicted.

62. Runoff coefficient is denoted by
A. p
B. n
C. k
D. h

Answer: C k
Explanation: the runoff coefficient can be defined as the ratio of runoff to rainfall.

63. is a graph showing variations of discharge with time.
A. rising limb graph
B. crest graph
C. hydraulic graph
D. gauge graph

Answer: C hydraulic graph
Explanation: hydrograph is a graph showing variations of discharge with time at a particular point of the stream. the hydrograph shows the time distribution of total run off at a point of measurement.

64. Calculate the torque which a shaft of 300 mm diameter can safely transmit, if the shear stress is 48 N / mm2.
A. 356 knm
B. 254 knm
C. 332 knm
D. 564 knm

Answer: B 254 knm
Explanation: given, the diameter of shaft d

65. What is the bending moment at end supports of a simply supported beam?
A. maximum
B. minimum
C. zero
D. uniform

Answer: C zero
Explanation: at the end supports, the moment (couple) developed is zero, because there is no distance to take the perpendicular acting load. as the distance is zero, the moment is obviously zero.

66. What is the maximum shear force, when a cantilever beam is loaded with udl throughout?
A. w×l
B. w
C. w/l
D. w+l

Answer: A w×l
Explanation: in cantilever beams, the maximum shear force occurs at the fixed end. in the free end, there is zero shear force. as we need to convert the udl in to load, we multiply the length of the cantilever beam with udl acting upon. for maximum shear force to obtain we ought to multiply load and distance and it surely occurs at the fixed end (w×l).

67. What is the maximum bending moment for simply supported beam carrying a point load “W” kN at its centre?
A. w knm
B. w/m knm
C. w×l knm
D. w×l/4 knm

Answer: D w×l/4 knm
Explanation: we know that in simply supported beams the maximum bm occurs at the central span.

68. How do point loads and udl be represented in SFD?
A. simple lines and curved lines
B. curved lines and inclined lines
C. simple lines and inclined lines
D. cant represent any more

Answer: C simple lines and inclined lines
Explanation: according to bis, the standard symbols used for sketching sfd are

69. curve is formed due to bending of over hanging beams.
A. elastic
B. plastic
C. flexural
D. axial

Answer: A elastic
Explanation: the line to which the longitudinal axis of a beam bends or deflects or deviates under given load is known as elastic curve on deflection curve. elastic curve can also be known as elastic line or elastic axis.

70. The relation between slope and maximum bending moment is
A. directly proportion
B. inversely proportion
C. relative proportion
D. mutual incidence

Answer: B inversely proportion
Explanation: the relationship between slope and maximum bending moment is inversely proportional because, for example in simply supported beams slope is maximum at supports and zero at midspan of a

71. What is the SF at support B?
A. 5 kn
B. 3 kn
C. 2 kn
D. 0 kn

Answer: D 0 kn
Explanation: total load = 2×2 = 4kn shear force at a = 4 kn ( same between a and c )

72. Where do the maximum BM occurs for the below diagram.
A. -54 knm
B. -92 knm
C. -105 knm
D. – 65 knm

Answer: C -105 knm
Explanation: moment at b = 0 moment at c = – (10 × 3) × (3/2)

73. The ratio of maximum deflection of a beam to its is called stiffness of the beam.
A. load
B. slope
C. span
D. reaction at the support

Answer: C span
Explanation: the stiffness of a beam is a measure of it’s resistance against deflection. the ratio of the maximum deflection of a beam to its span can be termed as stiffness of the beam.

74. Stiffness of the beam is inversely proportional to the of the beam.
A. slope
B. support reaction
C. deflection
D. load

Answer: C deflection
Explanation: stiffness of a beam is inversely proportional to the deflection. smaller the deflection in a beam due to given external load, greater is its stiffness.

75. The maximum should not exceed the permissible limit to the span of the beam.
A. slope
B. deflection
C. load
D. l bending moment

Answer: B deflection
Explanation: the maximum deflection of a loaded beam should not exceed the permissible limit in relation to the span of a beam. while designing the beam the designer

76. In cantilever beam the deflection occurs at
A. free end
B. point of loading
C. through out
D. fixed end

Answer: A free end
Explanation: deflection can be defined as

77. The maximum deflection in cantilever beam of span “l”m and loading at free end is “W” kN.
A. wl3/2ei
B. wl3/3ei
C. wl3/4ei
D. wl2/2ei

Answer: B wl3/3ei
Explanation: maximum deflection occurs at free end distance between centre of gravity of bending moment diagram and free end is x =

78. fluids are practical fluids
A. ideal
B. real
C. vortex
D. newtonian

Answer: B real
Explanation: these fluids possess properties such as viscosity, surface tension. they are compressible in nature. the certain amount of resistance is always offered by the fluids, they also possess shear stress. they are also known as practical fluids.

79. The inverse of specific weight of a fluid is
A. specific gravity
B. specific volume
C. compressibility
D. viscosity

Answer: B specific volume
Explanation: specific volume is the volume of the fluid by unit weight it is the reciprocal of specific weight is denoted by “v”. si units are m3/n.

80. Specific gravity of water is
A. 0.8
B. 1
C. 1.2
D. 1.5

Answer: B 1
Explanation: the specific gravity is also called as relative density. it is dimensionless quantity and it has no units. the specific gravity of water is the ratio of specific weight of fluid to specific weight of water, as both

81. Compute the maximum deflection at free end of a cantilever beam subjected to udl for entire span of l metres.
A. wl4/8ei
B. wl4/4ei
C. wl3/8ei
D. wl2/6ei

Answer: A wl4/8ei
Explanation: the slope at free end = a/ei = wl3/6ei

82. Which of the following is not an example of Malleability?
A. wrought iron
B. ornamental silver
C. torsteel
D. ornamental gold

Answer: C torsteel
Explanation: torsteel is an example of mechanical property ductility. the ductility is a property of a material by which material can be fractured into thin wires after undergoing a considerable deformation without any rupture.

83. Which of the following is not correct?
A. angles and t section are strong in bending
B. channels can be used only for light loads
C. i sections are most efficient and economical shapes
D. i section with cover plates are provided when large section modulus is required

Answer: A angles and t section are strong in bending
Explanation: angles and t section are weak in bending. channels can be used only for light loads. i sections (rolled and built-up) are most efficient and economical shapes. i section with cover plates are provided when large section modulus is required. generally, islb or ismb are provided in such cases.

84. Local buckling can be prevented by
A. limiting width-thickness ratio
B. increasing width-thickness ratio
C. changing material
D. changing load on member

Answer: C changing material
Explanation: local buckling of compression members of beam causes loss of integrity of

85. Which of the following is true?
A. in case of rolled section, less thickness of plate is adopted to prevent local buckling
B. for built-up section and cold formed section, longitudinal stiffeners are not provided to reduce width to smaller sizes
C. local buckling cannot be prevented by limiting width-thickness ratio
D. in case of rolled section, high thickness of plate is adopted to prevent local buckling

Answer: D in case of rolled section, high thickness of plate is adopted to prevent local buckling
Explanation: in case of rolled section, higher thickness of plate is adopted to prevent local buckling. local buckling cannot be prevented by limiting width-thickness ratio. for built-up section and cold formed section, longitudinal stiffeners are provided to reduce width to smaller sizes.

86. Which of the following is not true?
A. only plastic section can be used in intermediate frames
B. slender sections are preferred in hot rolled structural steelwork
C. compact sections can be used in simply supported beams
D. semi-compact sections can be used for elastic designs

Answer: B slender sections are preferred in hot rolled structural steelwork
Explanation: only plastic section can be used in intermediate frames which form collapse mechanism. compact sections can be used in simply supported beams which fail after reaching mp at one section. semi- compact sections can be used for elastic designs where section fails after reaching my at extreme fibres. slender sections are not preferred in hot rolled structural steelwork, but they are extensively used in cold formed members.

87. As per IS specification, the beam sections should be
A. not symmetrical about any principal axes
B. at least symmetrical about one of the principal axes
C. symmetrical about all principal axes
D. unsymmetrical about all principal axes

Answer: B at least symmetrical about one of the principal axes
Explanation: the beam sections should be at least symmetrical about one of the principal axes as per is specification. angle and t- sections are inherently weak in bending while channels can only be used for light loads.

88. A beam is said to be of uniform strength, if
A. b.m. is same throughout the beam
B. shear stress is the same through the beam
C. deflection is the same throughout the beam
D. bending stress is the same at every section along its longitudinal axis

Answer: D bending stress is the same at every section along its longitudinal axis
Explanation: beam is said to be uniform strength if at every section along its longitudinal axis, the bending stress is same.

89. Which stress comes when there is an eccentric load applied?
A. shear stress
B. bending stress
C. tensile stress
D. thermal stress

Answer: B bending stress
Explanation: when there is an eccentric load it means that the load is at some distance from the axis. this causes compression in one side and tension on the other. this causes bending stress.

90. What is the expression of the bending equation?
A. m/i = σ/y = e/r
B. m/r = σ/y = e/i
C. m/y = σ/r = e/i
D. m/i = σ/r = e/y

Answer: A m/i = σ/y = e/r
Explanation: the bending equation is given by m/i = σ/y = e/r

91. On bending of a beam, which is the layer which is neither elongated nor shortened?
A. axis of load
B. neutral axis
C. center of gravity
D. none of the mentioned

Answer: B neutral axis
Explanation: when a beam is in bending the layer in the direction of bending will be in compression and the other will be in tension. one side of the neutral axis will be shortened and the other will be elongated.

92. Consider a 250mmx15mmx10mm steel bar which is free to expand is heated from 15C to 40C. what will be developed?
A. compressive stress
B. tensile stress
C. shear stress
D. no stress

Answer: D no stress
Explanation: if we resist to expand then only stress will develop. here the bar is free to expand so there will be no stress.

93. The motion of the earth about its axis is periodic and simple harmonic.
A. true
B. false

Answer: B false
Explanation: the earth takes 24 hours to complete its rotation about its axis, but the concept of to and fro motion is absent, and hence the rotation of the earth is periodic and not simple harmonic.

94. An object of mass 0.2kg executes simple harmonic motion along the x-axis with a frequency of (25/π)Hz. At the position x = 0.04, the object has kinetic energy of 0.5J and potential energy 0.4J. The amplitude of oscillation is?
A. 6cm
B. 4cm
C. 8cm
D. 2cm

Answer: A 6cm
Explanation: total energy, e=2π2 mv2 a2 0.5+0.4=2π2×0.2×(25/π)2 a2 a2=0.9/(0.4×252) a=3/(2×25)=3/50 m=6cm.

95. A spring of force constant 800N/m has an extension of 5cm. The work done in extending it from 5cm to 15cm is?
A. 8j
B. 16j
C. 24j
D. 32j

Answer: A 8j
Explanation: at x1 = 5 cm, u1=1/2×k(x1)2=1/2×800×0.052=1j

96. A simple pendulum is attached to the roof of a lift. If the time period of oscillation, when the lift is stationary is T, then the frequency of oscillation when the lift falls freely, will be
A. zero
B. t
C. 1/t
D. ∞

Answer: A zero
Explanation: in a freely falling lift, g=0

97. A lightly damped oscillator with a frequency v is set in motion by a harmonic driving force of frequency v’. When v’ is lesser than v, then the response of the oscillator is controlled by
A. spring constant
B. inertia of the mass
C. oscillator frequency
D. damping coefficient

Answer: A spring constant
Explanation: frequency of driving force is lesser than frequency v of a damped oscillator. the vibrations are nearly in phase

98. What is the time period of a pendulum hanged in a satellite? (T is the time period on earth)
A. zero
B. t
C. infinite
D. t/√6

Answer: C infinite
Explanation: in a satellite, g= 0 t=2π√(l/g)=2π√(l/0)=∞.

99. Which of the following functions represents a simple harmonic oscillation?
A. sinωt-cosωt
B. sinωt+sin2ωt
C. sinωt-sin2ωt
D. sin2 ωt

  250+ TOP MCQs on Beats and Answers

Answer: A sinωt-cosωt
Explanation: y=sinωt-cosωt dy/dt=ωcosωt+ωsinωt

100. The ratio of velocity of sound in hydrogen and oxygen at STP is
A. 16:1
B. 8:1
C. 4:1
D. 2:1

Answer: C 4:1
Explanation: vh/vo = √(mo/mh)

101. The disc of a siren containing 60holes rotates at a constant speed of 360rpm. The emitted sound is in unison with a tuning fork of frequency.
A. 10hz
B. 360hz
C. 216hz
D. 60hz

Answer: B 360hz
Explanation: frequency of revolution of disc=360rpm=360/60rps=60rps

102. The quantity which does not change, when sound enters from one medium to another
A. wavelength
B. speed
C. frequency
D. velocity

Answer: C frequency
Explanation: frequency remains unchanged when sound travels from one medium to another.

103. If wave y=Acos(ωt+kx) Is moving along x- axis, the shapes of a pulse at t=0 and t=2s.
A. are different
B. are same
C. may not be the same
D. unpredictable

Answer: B are same
Explanation: the shapes of y-x graph remains the same at t=0 and t=2s.

104. y1=4sin(ωt+kx), y2=-4cos(ωt+kx), the phase difference is
A. π/2
B. 3π/2
C. π
D. zero

Answer: B 3π/2
Explanation: y1=4sin(ωt+kx) y2=-4cos(ωt+kx)

105. A wave equation is y=0.1sin[100πt-kx] and wave velocity is 100m/s, its number is equal to
A. 1/m
B. 2/m
C. π/m
D. 2π/m

Answer: C π/m
Explanation: y=0.1sin[100πt-kx] y=asin(ωt-kx)

106. The fundamental frequency of a sonometer wire is n. If the tension is made 3 times and length and diameter are also increased 3 times, the new frequency will be
A. 3n
B. n/3√3
C. n/3
D. √3 n

Answer: B n/3√3
Explanation: n=1/ld×√(t/πρ) n‘=1/(3l×3d)×√(3t/πρ)=√3/9×n=1/(3√3) n.

107. Which of the following Einstein’s coefficient represents spontaneous emission?
A. a12
B. a21
C. b12
D. b21

Answer: B a21
Explanation: a21 represents the spontaneous emission of photons. a12 signifies spontaneous absorption.b12 is for stimulated absorption while b21 is for stimulated emission.

108. Which law is used for achieving the relation between the Einstein’s coefficients?
A. heisenberg’s uncertainty principle
B. planck’s radiation law
C. einstein’s equation
D. quantum law

Answer: B planck’s radiation law
Explanation: planck’s radiation law, which

109. The probability of spontaneous emission increases rapidly with the energy difference between the two states.
A. true
B. false

Answer: A true
Explanation: from einstein’s relation we know that the ratio of einstein’s coefficients

110. What is the unit for the coefficient of stimulated emission?
A. s-2
B. m3 s-2
C. j−1 m3
D. j−1 m3 s-2

Answer: D j−1 m3 s-2
Explanation: for stimulated emission, the

111. Which Einstein’s coefficient should be used in this case?
A. a12
B. a21
C. b12
D. b21

Answer: D b21
Explanation: the given figure shows stimulated emission. hence, the einstein coefficient for stimulated emission is b21. if it had been spontaneous emission, then a21 would have been used.

112. A cylindrical cavity resonator can be constructed using a circular waveguide.
A. shorted at both the ends
B. open at both the ends
C. matched at both the ends
D. none of the mentioned

Answer: A shorted at both the ends
Explanation: a cylindrical cavity resonator is formed by shorting both the ends of the cylindrical cavity because open ends may result in radiation losses in the cavity.

113. The dominant mode in the cylindrical cavity resonator is TE101 mode.
A. true
B. false

Answer: B false
Explanation: the dominant mode of propagation in a circular waveguide is te111 mode. hence, the dominant mode of resonance in a cylindrical cavity made of a circular waveguide is te111 mode. in a

114. Circular cavities are used for microwave frequency meters.
A. true
B. false

Answer: A true
Explanation: circular cavities are used for microwave frequency meters. the cavity is constructed with a movable top wall to allow the mechanical tuning of the resonant frequency.

115. The mode of the circular cavity resonator used in frequency meters is:
A. te011 mode
B. te101 mode
C. te111 mode
D. tm111 mode

Answer: A te011 mode
Explanation: frequency resolution of a frequency meter is determined from its quality factor. q factor of te011 mode is much greater than the quality factor of the dominant mode of propagation.

116. The propagation constant of TEmn mode of propagation for a cylindrical cavity resonator is:
A. 2)
B. √ pnm/a
C. √ (k2+(pnm/a)2)
D. none of the mentioned

Answer: A 2)
Explanation: the propagation constant for a circular cavity depends on the radius of the cavity, and the wave number. if the mode of propagation is known and the dimension of the cavity is known then the propagation constant can be found out.

117. A circular cavity resonator is filled with a dielectric of 2.08 and is operating at 5GHz of frequency. Then the wave number is:
A. 181
B. 151
C. 161
D. 216

Answer: B 151
Explanation: wave number for a circular cavity resonator is given by the expression 2πf011√∈r/c. substituting the given values in the above expression; the wave number of the cavity resonator is 151.

118. Given that the wave number of a circular cavity resonator is 151 (TE011 mode), and the length of the cavity is twice the radius of the cavity, the radius of the circular cavity operating at 5GHz frequency is:
A. 2.1 cm
B. 1.7 cm
C. 2.84 cm
D. insufficient data

Answer: D insufficient data
Explanation: for a circular cavity resonator, wave number is given by √( (p01/a)2 +(π/d)2). p01 for the given mode of resonance is 3.832.

119. A circular cavity resonator has a wave number of 151, radius of 2.74 cm, and surface resistance of 0.0184Ω. If the cavity is filled with a dielectric of 2.01, then unloaded Q due to conductor loss is:
A. 25490
B. 21460
C. 29390
D. none of the mentioned

Answer: C 29390
Explanation: unloaded q of a circular resonator due to conductor loss is given by ka/2rs. is the intrinsic impedance of the medium. substituting the given values in the equation for loaded q, value is 29390.

120. If unloaded Q due to conductor loss and unloaded Q due to dielectric loss is 29390 and 2500 respectively, then the total unloaded Q of the circular cavity is:
A. 2500
B. 29390
C. 2300
D. 31890

Answer: C 2300
Explanation: the total unloaded q of a circular cavity resonator is given by the expression (q -1+ q -1)-1. substituting the

121. The energy-level occupation for a semiconductor in thermal equilibrium is described by the
A. boltzmann distribution function
B. probability distribution function
C. fermi-dirac distribution function
D. cumulative distribution function

Answer: C fermi-dirac distribution function
Explanation: for a semiconductor in thermal equilibrium, the probability p(e) that an electron gains sufficient thermal energy at an absolute temperature so as to occupy a particular energy level e, is given by the fermi-dirac distribution. it is given by-

122. What is done to create an extrinsic semiconductor?
A. refractive index is decreased
B. doping the material with impurities
C. increase the band-gap of the material
D. stimulated emission

Answer: B doping the material with impurities
Explanation: an intrinsic semiconductor is a pure semiconductor. an extrinsic semiconductor is obtained by doping the material with impurity atoms. these impurity atoms create either free electrons or holes.

123. The majority of the carriers in a p-type semiconductor are
A. holes
B. electrons
C. photons
D. neutrons

Answer: A holes
Explanation: the impurities can be either donor impurities or acceptor impurities.

124. is used when the optical emission results from the application of electric field.
A. radiation
B. efficiency
C. electro-luminescence
D. magnetron oscillator

Answer: C electro-luminescence
Explanation: electro-luminescence is encouraged by selecting an appropriate semiconductor material. direct band-gap semiconductors are used for this purpose. in band-to-band recombination, the energy is released with the creation of photon. this emission of light is known as electroluminescence.

125. The recombination in indirect band-gap semiconductors is slow.
A. true
B. false

Answer: A true
Explanation: in an indirect band-gap semiconductor, the maximum and minimum energies occur at different values of crystal momentum. however, three-particle recombination process is far less probable than the two-particle process exhibited by direct band-gap semiconductors. hence, the recombination in an indirect band-gap semiconductor is relatively slow.

126. Calculate the radioactive minority carrier lifetime in gallium arsenide when the minority carriers are electrons injected into a p-type semiconductor region which has a hole concentration of 1018cm-3. The recombination coefficient for gallium arsenide is 7.21*10-10cm3s-1.
A. 2ns
B. 1.39ns
C. 1.56ns
D. 2.12ms

Answer: B 1.39ns
Explanation: the radioactive minority carrier lifetime ςrconsidering the p-type region is given by-

127. Which impurity is added to gallium phosphide to make it an efficient light emitter?
A. silicon
B. hydrogen
C. nitrogen
D. phosphorus

Answer: C nitrogen
Explanation: an indirect band-gap semiconductor may be made into an electro- luminescent material by the addition of impurity centers which will convert it into a

128. Population inversion is obtained at a p-n junction by
A. heavy doping of p-type material
B. heavy doping of n-type material
C. light doping of p-type material
D. heavy doping of both p-type and n-type material

Answer: D heavy doping of both p-type and n-type material
Explanation: population inversion at p-n junction is obtained by heavy doping of both p-type and n-type material. heavy p-type doping with acceptor impurities causes a lowering of the fermi-level between the filled and empty states into the valence band.

129. A GaAs injection laser has a threshold current density of 2.5*103Acm-2 and length and width of the cavity is 240μm and 110μm respectively. Find the threshold current for the device.
A. 663 ma
B. 660 ma
C. 664 ma
D. 712 ma

Answer: B 660 ma
Explanation: the threshold current is denoted by ith. it is given by-

130. A GaAs injection laser with an optical cavity has refractive index of 3.6. Calculate the reflectivity for normal incidence of the plane wave on the GaAs-air interface.
A. 0.61
B. 0.12
C. 0.32
D. 0.48

Answer: C 0.32
Explanation: the reflectivity for normal incidence of the plane wave on the gaas-air interface is given by-

131. A homo-junction is an interface between two adjoining single-crystal semiconductors with different band-gap energies.
A. true
B. false

Answer: B false
Explanation: the photo-emissive properties of a single p-n junction fabricated from a single-crystal semiconductor material are called as homo-junction. a hetero-junction is an interface between two single-crystal semiconductors with different band-gap energies. the devices which are fabricated with hetero-junctions are said to have hetero- structure.

132. How many types of hetero-junctions are available?
A. two
B. one
C. three
D. four

Answer: A two
Explanation: hetero-junctions are classified into an isotype and an-isotype. the isotype hetero-junctions are also called as n-n or p-p junction. the an-isotype hetero-junctions are called as p-n junction with large band-gap energies.

133. The system is best developed and is used for fabricating both lasers and LEDs for the shorter wavelength region.
A. inp
B. gasb
C. gaas/gasb
D. gaas/alga as dh

Answer: D gaas/alga as dh
Explanation: for dh device fabrication, materials such as gaas, alga as are used. the band-gap in this material may be tailored to span the entire wavelength band by changing the alga composition. thus, gaas/ alga as dh system is used for fabrication of lasers and leds for shorter wavelength region (0.8μm-0.9μm).

134. What is the principle of fibre optical communication?
A. frequency modulation
B. population inversion
C. total internal reflection
D. doppler effect

Answer: C total internal reflection
Explanation: in optical fibres, the light entering the fibre does not encounter any new surfaces, but repeatedly they hit the same surface. the reason for confining the light beam inside the fibres is the total internal reflection.

135. What is the other name for a maximum external incident angle?
A. optical angle
B. total internal reflection angle
C. refraction angle
D. wave guide acceptance angle

Answer: D wave guide acceptance angle
Explanation: only this rays which pass within the acceptance angle will be totally reflected. therefore, light incident on the core within the maximum external incident angle

136. A single mode fibre has low intermodal dispersion than multimode.
A. true
B. false

Answer: A true
Explanation: in both single and multimode fibres the refractive indices will be in step by step. since a single mode has less dispersion than multimode, the single mode step index fibre also has low intermodal dispersion compared to multimode step index fibre.

137. How does the refractive index vary in Graded Index fibre?
A. tangentially
B. radially
C. longitudinally
D. transversely

Answer: B radially
Explanation: the refractive index of the core is maximum along the fibre axis and it gradually decreases. here the refractive index varies radially from the axis of the fibre.

138. Which of the following has more distortion?
A. single step-index fibre
B. graded index fibre
C. multimode step-index fibre
D. glass fibre

Answer: C multimode step-index fibre
Explanation: when rays travel through longer distances there will be some difference in reflected angles. hence high angle rays arrive later than low angle rays. therefore the signal pulses are broadened thereby results in a distorted output.

139. In which of the following there is no distortion?
A. graded index fibre
B. multimode step-index fibre
C. single step-index fibre
D. glass fibre

Answer: A graded index fibre
Explanation: the light travels with different speeds in different paths because of the variation in their refractive indices. at the outer edge it travels faster than near the centre but almost all the rays reach the exit end at the same time due to the helical path. thus, there is no dispersion in the pulses and hence the output is not a distorted output.

140. Which of the following loss occurs inside the fibre?
A. radiative loss
B. scattering
C. absorption
D. attenuation

Answer: B scattering
Explanation: scattering is a wavelength dependent loss. since the glass used in the fabrication of fibres, the disordered structure of glass will make some vibrations in the refractive index inside the fibre. this causes rayleigh scattering.

141. What causes microscopic bend?
A. uniform pressure
B. non-uniform volume
C. uniform volume
D. non-uniform pressure

Answer: D non-uniform pressure
Explanation: micro-bends losses are caused due to non-uniformities inside the fibre. this micro-bends in fibre appears due to non- uniform pressures created during the cabling of fibre.

142. When more than one mode is propagating, how is it dispersed?
A. dispersion
B. inter-modal dispersion
C. material dispersion
D. waveguide dispersion

Answer: B inter-modal dispersion
Explanation: when more than one mode is propagating through a fibre, then inter modal dispersion will occur. since many modes are propagating, they will have different wavelengths and will take different time to propagate through the fibre.

143. A fibre optic telephone transmission can handle more than thousands of voice channels.
A. true
B. false

Answer: A true
Explanation: optical fibre has larger bandwidth hence it can handle a large number of channels for communication.

144. Which of the following is known as fibre optic back bone?
A. telecommunication
B. cable television
C. delay lines
D. bus topology

Answer: D bus topology
Explanation: each computer on the network is connected to the rest of the computers by the optical wiring scheme called bus topology, which is an application known as fibre optic back bone.

145. Calculate the numerical aperture of an optical fibre whose core and cladding are made of materials of refractive index 1.6 and
A. 0.55677
B. 55.77
C. 0.2458
D. 0.647852

Answer: A 0.55677
Explanation: numerical aperture =

146. A step-index fibre has a numerical aperture of 0.26, a core refractive index of 1.5 and a core diameter of 100micrometer. Calculate the acceptance angle.
A. 1.47°
B. 15.07°
C. 2.18°
D. 24.15°

Answer: B 15.07°
Explanation: sin i = (numerical aperture)/n sin i = 15.07°.

147. Multimode step index fiber has
A. large core diameter & large numerical aperture
B. large core diameter and small numerical aperture
C. small core diameter and large numerical aperture
D. small core diameter & small numerical aperture

Answer: A large core diameter & large numerical aperture
Explanation: multimode step-index fiber has large core diameter and large numerical aperture. these parameters provides efficient coupling to inherent light sources such as led’s.

148. 9 LOSSES ASSOCIATED WITH OPTICAL FIBERS
A. 1.2 to 90 db km-1 at wavelength 0.69μm
B. 3.2 to 30 db km-1 at wavelength 0.59μm
C. 2.6 to 50 db km-1 at wavelength 0.85μm
D. 1.6 to 60 db km-1 at wavelength 0.90μm

Answer: C 2.6 to 50 db km-1 at wavelength 0.85μm
Explanation: a multimode step index fibers show an attenuation variation in range of 2.6 to 50dbkm-1. the wide variation in attenuation is due to the large differences both within and between the two overall

149. Multimode step index fiber has a large core diameter of range is
A. 100 to 300 μm
B. 100 to 300 nm
C. 200 to 500 μm
D. 200 to 500 nm

Answer: A 100 to 300 μm
Explanation: a multimode step index fiber has a core diameter range of 100 to 300μm. this is to facilitate efficient coupling to inherent light sources.

150. Multimode step index fibers have a
A. better than multimode step index fibers
B. same as multimode step index fibers
C. lesser than multimode step index fibers
D. negligible

Answer: A better than multimode step index fibers
Explanation: multimode graded index fibers use a constant grading factor. performance characteristics of multimode graded index fibers are better than those of multimode step index fibers due to index graded and lower attenuation.

151. Multimode graded index fibers with wavelength of 0.85μm have numerical aperture of 0.29 have core/cladding diameter of
A. 62.5 μm/125 μm
B. 100 μm/140 μm
C. 85 μm/125 μm
D. 50 μm/125μm

Answer: B 100 μm/140 μm
Explanation: multimode graded index fibers with numerical aperture 0.29 having a core/cladding diameter of 100μm/140μm.

152. Multimode graded index fibers use incoherent source only.
A. true
B. false

Answer: B false
Explanation: multimode graded index fibers are used for short haul and medium to high bandwidth applications. small haul applications require leds and low accuracy lasers. thus either incoherent or incoherent sources like led’s or injection laser diode are used.

153. In single mode fibers, which is the most beneficial index profile?
A. step index
B. graded index
C. step and graded index
D. coaxial cable

Answer: B graded index
Explanation: in single mode fibers, graded index profile is more beneficial as compared to step index. this is because graded index profile provides dispersion-modified-single mode fibers.

154. The fibers mostly not used nowadays for optical fiber communication system are
A. single mode fibers
B. multimode step fibers
C. coaxial cables
D. multimode graded index fibers

Answer: A single mode fibers
Explanation: single mode fibers are used to produce polarization maintaining fibers which make them expensive. also the alternative to them are multimode fibers which are complex but accurate. so, single-mode fibers are not generally utilized in optical fiber communication.

155. Single mode fibers allow single mode propagation; the cladding diameter must be at least
A. twice the core diameter
B. thrice the core diameter
C. five times the core diameter
D. ten times the core diameter

Answer: D ten times the core diameter
Explanation: the cladding diameter in single mode fiber must be ten times the core diameter. larger ratios contribute to accurate propagation of light. these dimension ratios must be there so as to avoid losses from the vanishing fields.

156. A fiber which is referred as non- dispersive shifted fiber is?
A. coaxial cables
B. standard single mode fibers
C. standard multimode fibers
D. non zero dispersion shifted fibers

Answer: B standard single mode fibers
Explanation: a standard single mode fiber having step index profile is known as non- dispersion shifted fiber. as these fibers have a zero dispersion wavelength of 1.31μm and so are preferred for single-wavelength transmission in o-band.

157. Standard single mode fibers (SSMF) are utilized mainly for operation in
A. c-band
B. l-band
C. o-band
D. c-band and l-band

Answer: C o-band
Explanation: ssmfs are utilized for operation in o-band only. it shows high dispersion in the range of 16 to 20ps/nm/km in c-band and l-band. so ssmfs are used in o-band.

158. Fiber mostly suited in single-wavelength transmission in O-band is?
A. low-water-peak non dispersion-shifted fibers
B. standard single mode fibers
C. low minimized fibers
D. non-zero-dispersion-shifted fibers

Answer: B standard single mode fibers
Explanation: standard single mode fibers with a step index profile are called non dispersion shifted fiber and it is particularly used for single wavelength transmission in o- band and as if has a zero-dispersion wavelength at 1.31μm.

159. Fluoride glass is used with
A. ir waves
B. uv rays
C. normal light
D. all of the mentioned

Answer: A ir waves
Explanation: flouride glass is suitable for ir rays of wavelength upto 3200 nm.

160. Silica glass of hydroxyl concentration can be used for of wavelength.
A. 100 nm to 250 nm
B. 250 nm to 800 nm
C. 800 nm to 1500 nm
D. 100 nm to 3400 nm

Answer: B 250 nm to 800 nm
Explanation: silica glass with hydroxyl concentration is used for wavelength 250 nm to 800 nm.

161. OTDR stands for
A. optical time domain reflectometer
B. optical transfer data rate
C. optical time data registers
D. none of the mentioned

Answer: A optical time domain reflectometer
Explanation: otdr is the short form of optical time domain reflectometer.

162. Which of the following is not correct for fibre optic sensors?
A. immune to electro magnetic interference
B. immune to radiation hazard
C. can be used in harsh environments
D. none of the mentioned

Answer: D none of the mentioned
Explanation: all of the mentioned are qualities of fibre optic sensors.

163. Epoxy material in fibre optics is intended for
A. better optical properties
B. better reflection
C. better sealing
D. reducing noise

Answer: C better sealing
Explanation: polished epoxy seal provides liquid and air tight seal.

164. Plastics optical cables can be used for
A. short range
B. medium range of distance
C. long range of distance
D. very high range of distance

Answer: A short range
Explanation: plastic optical cables are manufacturing for short range purposes.

165. Which of the following represents loss associated with glass fibres?
A. 3 db/km
B. 10 db/km
C. 0 db/km
D. 50 db/km

Answer: A 3 db/km
Explanation: glass fibres have a net loss of 3 db on every single kilometre.

166. Loss associated with plastic fibre is less than glass fibres.
A. true
B. false

Answer: B false
Explanation: loss associated with plastic fibre is about 100-1250 db/km and it is several times larger than glass fibres.

167. Cladding in glass fibre have high refractive index than the core.
A. true
B. false

Answer: B false
Explanation: cladding in glass fibre is always kept at a low refractive index than the core.

168. The transfer of heat between two bodies in direct contact is called
A. radiation
B. convection
C. conduction
D. none of the mentioned

Answer: C conduction
Explanation: this is the definition of conduction.

169. In the equation, dQ=TdX
A. dq is an inexact differential
B. dx is an exact differential
C. x is an extensive property
D. all of the mentioned

Answer: D all of the mentioned
Explanation: this is because heat transfer is a path function.

170. The transfer of heat between a wall and a fluid system in motion is called
A. radiation
B. convection
C. conduction
D. none of the mentioned

Answer: B convection
Explanation: this is the definition of convection.

171. The specific heat of the substance is defined as the amount of heat required to raise a unit mass of the substance through a unit rise in temperature.
A. true
B. false

Answer: A true
Explanation: c=q/(m*Δt).

172. Heat and work are
A. path functions
B. inexact differentials
C. depend upon the path followed
D. all of the mentioned

Answer: D all of the mentioned
Explanation: it is an important point to remember regarding heat and work transfer.

173. Latent heat is taken at
A. constant temperature
B. constant pressure
C. both of the mentioned
D. none of the mentioned

Answer: C both of the mentioned
Explanation: the latent heat is heat transfer required to cause a phase change in a unit mass of substance at a constant pressure and temperature.

174. Which of the following is true?
A. latent heat of fusion is not much affected by pressure
B. latent heat of vaporization is highly sensitive to pressure
C. both of the mentioned
D. none of the mentioned

Answer: C both of the mentioned
Explanation: it is a general fact about latent

175. Heat transfer and work transfer are
A. boundary phenomena
B. energy interactions
C. energy in the transit
D. all of the mentioned

Answer: D all of the mentioned
Explanation: it is an important point to remember regarding heat and work transfer.

176. A faulty thermometer has its fixed points marked as 5° and 95°. The temperature of a body as measured by the faulty thermometer is 59°. Find the correct temperature of the body on a Celsius scale.
A. 60°c
B. 40°c
C. 20°c
D. 0°c

Answer: A 60°c
Explanation: (tc-0)/(100-0)=(temperature on faulty scale-lower fixed point)/(upper fixed point-lower fixed point)

177. Temperature is a microscopic concept.
A. true
B. false

Answer: B false
Explanation: temperature is a macroscopic concept. it is related to the average kinetic energy of a large number of molecules forming a system. it is not possible to define the temperature for a single molecule.

178. 2 THERMAL EXPANSION OF SOLIDS AND LIQUIDS
A. high heat capacity
B. no heat capacity
C. small heat capacity
D. varying heat capacity

Answer: C small heat capacity
Explanation: the thermometer bulb having small heat capacity will absorb less heat from the body whose temperature is to be measured. hence the temperature of that body will practically remain unchanged.

179. Calorie is defined as the amount of heat required to raise the temperature of 1g of water by 1°C and it is defined under which of the following conditions?
A. from 14.5°c to 15.5°c at 760mm of hg
B. from 98.5°c to 99.5°c at 760mm of hg
C. from 13.5°c to 14.5°c at 76mm of hg
D. from 3.5°c to 4.5°c at 76mm of hg

Answer: A from 14.5°c to 15.5°c at 760mm of hg
Explanation: one calorie is defined as the heat required to raise the temperature of 1g of water from 14.5°c to 15.5° at 760mm of hg.

180. Compared to burn due to air at 100°C, a burn due to steam at 100°C is
A. more dangerous
B. less dangerous
C. equally dangerous
D. not dangerous

Answer: A more dangerous
Explanation: compared to burn due to air at 100°c, a burn due to steam at 100°c is more dangerous due to the additional heat possessed by steam.

181. 540g of ice at 0°C is mixed with 540g of water at 80°C. What is the final temperature of the mixture?
A. 0°c
B. 40°c
C. 80°c
D. less than 0°c

Answer: A 0°c
Explanation: heat gained by ice = heat lost by water at 80°c 540×80+540×1×θ=540×1×(80-θ)

182. If the sun were to increase in temperature from T to 2T and its radius from R to 2R, then the ratio of the radiant energy received on earth to what it was previously, will be
A. 4
B. 16
C. 32
D. 64

Answer: D 64
Explanation: energy radiated by the sun per second,

183. On a hilly region, water boils at 95°C. What is the temperature expressed in Fahrenheit?
A. 100°f
B. 203°f
C. 150°f
D. 20.3°f

Answer: B 203°f
Explanation: (f-32)/9=c/5=95/5 f = 171+32 = 203°f.

184. Temperatures of two stars are in ratio 3:2. If wavelength of maximum intensity of first body is 4000 Å, what is corresponding wavelength of second body?
A. 9000 Å
B. 6000 Å
C. 2000 Å
D. 8000 Å

Answer: B 6000 Å
Explanation: ((ʎm)‘)/ʎm = t/t‘ = 3/2

185. Identify the given joint in Concrete Structures.
A. horizontal construction joint
B. vertical construction joint
C. expansion construction joint
D. water tank joint

Answer: A horizontal construction joint
Explanation: the construction joints are provided at locations were the construction is

186. Identify the given joint in Concrete Structures.
A. horizontal construction joint
B. expansion construction joint
C. vertical construction joint
D. water tank joint

Answer: C vertical construction joint
Explanation: the construction joint maybe horizontal or vertical. for an inclined or curved member of the joint should be at right angle to the axis of the member. it is necessary to determine the location of construction joints well in advance for the viewpoint of structural stability.

187. Identify the given type of joint in Concrete Structures.
A. l beam construction joint
B. t beam construction joint
C. expansion joint
D. contraction joint

Answer: B t beam construction joint
Explanation: in case of t-beams, the ribs should be filled with concrete first and in the slabs forming the flanges can be filled up to the centre of the ribs. if a construction joint between slab and beam becomes unavoidable

188. Identify the given joint in Concrete Structures.
A. expansion joint
B. contraction joint
C. water tank joint
D. vertical construction joint

Answer: C water tank joint
Explanation: for water tanks and other structured which store water, the strips of copper, aluminium, galvanized iron or other corrosion resistant material known as water stops or waterbars, are placed in construction joint as shown in given figure above.

189. Identify the given joint in Concrete Structures.
A. partial contraction joint
B. complete contraction joint
C. horizontal construction joint
D. dummy joint

Answer: D dummy joint
Explanation: above figure shows another form of contraction joint. it is also known as a dummy joint and in this case, a groove of 3 mm width is created in the concrete member to act as a joint. the groove is filled with the joint filler and its depth is about 1/3 to 1/5 of the total thickness of the member.

190. For water tanks and other structure which store water, the strips of copper, aluminium, galvanized iron or other collision resistance material, known as the
A. joints
B. waterstops
C. dowels
D. fillers

Answer: B waterstops
Explanation: the function of waterstops is to seal the joint against the passage of water.

191. The expansion and contraction joints generally consist of some elastic material, known as which should be compressible, rigid, cellular and Resilient.
A. keys
B. joint filler
C. keys
D. fillers

Answer: B joint filler
Explanation: the usual joint filler are built- in strips of metal, bitumen treated felt, cane fibre board, cork bound with rubber or resin, dehydrated cork, natural cork, softwood free from knots, etc.

192. The are provided in expansion and contraction joints to transfer the load.
A. dowels
B. fillers
C. joint filler
D. waterbars

Answer: A dowels
Explanation: the contraction joints are installed to allow for shrinkage movement in the structure. it may either be a complete contraction joint or a partial construction joint. in the former case, there is complete discontinuity of both concrete and steel.

193. The is a mixture of cement and sand, the usual proportion being 1:3.
A. mortar
B. slurry
C. gunite
D. concrete

Answer: C gunite
Explanation: a cement gun is used to deposit the gunite mixture on the concrete surface under pressure of about 20 n/cm2 to 30 n/cm2. the cement is mixed with slightly moist sand and the necessary water is added as the mixture comes out from the cement gun.

194. Measurement of elevated temperatures is defined as
A. thermometry
B. pyrometry
C. metallography
D. radiography

Answer: B pyrometry
Explanation: pyrometry deals with elevated temperatures, generally around 950 f. the apparatus that is used in this process is known as a pyrometer. thermometry generally deals with the measurement of temperatures below 950 f.

195. What temperature is the dark orange color associated with?
A. 1475 f
B. 1650 f
C. 1750 f
D. 1800 f

Answer: B 1650 f
Explanation: temperature of metals can be estimated by simply looking at the color of the hot body. dark orange is associated with a temperature of about 1150 f, while for bright cherry, orange, and yellow it is 1475 f, 1750 f, and 1800 f correspondingly.

196. Bimetallic strips contain as a metal.
A. muntz metal
B. yellow brass
C. bronze
D. aluminum

Answer: B yellow brass
Explanation: bimetallic strips include invar as one metal and yellow brass as another. for higher temperatures, nickel alloy can be used. these can be used in temperatures ranging from -100 f to 1000 f.

197. Why is invar used in bimetallic strips?
A. low density
B. low coefficient of expansion
C. high-temperature resistance
D. high abrasion resistance

Answer: B low coefficient of expansion
Explanation: most bimetallic strips are composed of invar and yellow brass as metal. invar has the advantage of low coefficient of expansion, whereas yellow brass has the ability to be used at low temperatures.

198. is commonly used in liquid- expansion thermometers.
A. bourdon tube
B. spinning rotor gauge
C. mcleod gauge
D. manometer

Answer: A bourdon tube
Explanation: liquid-expansion thermometers consist of a bulb and an expansible device.

199. Resistance thermometer generally makes use of for the measurement of resistance.
A. potentiometer
B. adruino
C. diode bridge
D. wheatstone bridge

Answer: D wheatstone bridge
Explanation: resistance thermometers are based on the principle of increase in electrical resistance with increasing temperature. it consists of a resistance coil mounted in a protecting tube which is connected to a resistance measuring instrument. generally, wheatstone bridge is used in this process.

  250+ TOP MCQs on Simple Harmonic Oscillation and Answers

200. Which of these materials is not used for resistance coils?
A. nickel
B. copper
C. titanium
D. platinum

Answer: C titanium
Explanation: resistance coils are generally made of nickel, copper, or platinum. nickel and copper can be used in the temperature range of 150-500 f, whereas platinum can be used between -350 to 1100 f.

201. Liquid expansion thermometers are filled with
A. mercury
B. amalgam
C. gallium
D. cesium

Answer: A mercury
Explanation: the liquid-expansion thermometer has the entire system filled with an organic liquid or mercury. mercury is used at a temperature range of -35 to 950 f. alcohol and creosote are used at -110 to 160 f, and 20 to 400 f respectively.

202. The sun shines on a 150 m2 road surface so it is at 45°C. Below the 5cm thick asphalt(average conductivity of 0.06 W/m K), is a layer of rubbles at 15°C. Find the rate of
A. 5300 w
B. 5400 w
C. 5500 w
D. 5600 w

Answer: B 5400 w
Explanation: there is conduction through the asphalt layer.

203. A water-heater is covered with insulation boards over a total surface area of 3 m2. The inside board surface is at 75°C and the outside being at 20°C and the conductivity of material being 0.08 W/m K. Find the thickness of board to limit the heat transfer loss to 200 W ?
A. 0.036 m
B. 0.046 m
C. 0.056 m
D. 0.066 m

Answer: D 0.066 m
Explanation: steady state conduction through board.

204. A large heat exchanger transfers a total of 100 MW. Assume the wall separating steam and seawater is 4 mm of steel, conductivity 15 W/m K and that a maximum of 5°C difference between the two fluids is allowed. Find the required minimum area for the heat transfer.
A. 180 m2
B. 280 m2
C. 380 m2
D. 480 m2

Answer: D 480 m2
Explanation: steady conduction q = k a ∆t/∆x ⇒ Α = q ∆x / k∆Τ

205. The black grille on the back of a refrigerator has a surface temperature of 35°C with a surface area of 1 m2. Heat transfer to the room air at 20°C takes place with convective heat transfer coefficient of 15 W/Km^2. How much energy is removed during 15 minutes of operation?
A. 202.5 kj
B. 212.5 kj
C. 222.5 kj
D. 232.5 kj

Answer: A 202.5 kj
Explanation: q = ha ∆t ∆t, q = 15 × 1 × (35-20)×15×60 = 202500 j = 202.5 kj.

206. A small light bulb (25 W) inside a refrigerator is kept on and 50 W of energy from the outside seeps into the refrigerated space. How much of temperature difference to the ambient(at 20°C) must the refrigerator have in its heat exchanger having an area of 1 m2 and heat transfer coefficient of 15 W/Km2 to reject the leak of energy.
A. 0°c
B. 5°c
C. 10°c
D. 15°c

Answer: B 5°c
Explanation: total energy that goes out = 50+25 = 75 w

207. As the car slows down, the brake shoe and steel drum continuously absorbs 25 W. Assume a total outside surface area of 0.1 m2 with a convective heat transfer coefficient of 10 W/Km2 to the air at 20°C. How hot does the outside brake and drum surface become when steady conditions are reached?
A. 25°c
B. 35°c
C. 45°c
D. 55°c

Answer: C 45°c
Explanation: ∆Τ = heat / ha hence ∆t = [ Τ(brake) − 20 ] = 25/(10 × 0.1) = 25°c Τ(brake) = 20 + 25 = 45°c.

208. A burning wood in the fireplace has a surface temperature of 450°C. Assume the emissivity to be 1 and find the radiant emission of energy per unit area.
A. 15.5 kw/m2
B. 16.5 kw/m2
C. 17.5 kw/m2
D. 18.5 kw/m2

Answer: A 15.5 kw/m2
Explanation: q /a = 1 × σ t^4

209. 5 cm in diameter, through which 400 W of electric energy is deposited. Assume the surface emissivity to be 0.9 and neglecting incoming radiation, find the rod surface temperature?
A. 700k
B. 800k
C. 900k
D. 1000k

Answer: D 1000k
Explanation: outgoing power equals electric power

210. A water-heater is covered up with insulation boards over a total surface area of 3 m2. The inside board surface is at 75°C and the outside surface is at 20°C and the board material has a conductivity of 0.08 W/m K. How thick a board should it be to limit the heat transfer loss to 200 W ?
A. 0.066 m
B. 0.166 m
C. 0.266 m
D. 0.366 m

Answer: A 0.066 m
Explanation: steady state conduction through a single layer board.

211. 16 W/m K, with a temperature difference between the two sides of 20°C.
A. 113 w/m2
B. 213 w/m2
C. 230 w/m2
D. 312 w/m2

Answer: B 213 w/m2
Explanation: . q = .q/a = k Δt/Δx = 0.16 wm /k × 20k/0.015 m = 213 w/m2.

212. A 2 m2 window has a surface temperature of 15°C and the outside wind is blowing air at 2°C across it with a convection heat transfer coefficient of h = 125 W/m2K. What is the total heat transfer loss?
A. 2350 w
B. 1250 w
C. 2250 w
D. 3250 w

Answer: D 3250 w
Explanation: .q = h a Δt = 125 w/m2k × 2 m2 × (15 – 2) k = 3250 w.

213. A radiant heating lamp has a surface temperature of 1000 K with ε = 0.8. How large a surface area is needed to provide 250 W of radiation heat transfer?
A. 0.0035 m2
B. 0.0045 m2
C. 0.0055 m2
D. 0.0065 m2

Answer: C 0.0055 m2
Explanation: .q = εσat^4

214. 12 W/m K Thermal diffusivity = 5.16 * 10 -7 m2/s
A. 43.07 hours
B. 53.07 hours
C. 63.07 hours
D. 73.07 hours

Answer: A 43.07 hours
Explanation: t – t a/t 0 – t a = 0.86. also, α t/l 2 = 0.32.

215. 5 W/m K
A. 245 w/m2k
B. 235 w/m2k
C. 225 w/m2k
D. 215 w/m2k

Answer: C 225 w/m2k
Explanation: l = volume/surface area = r/3. so, h = (0.1) (k) (3)/r.

216. The transient response of a solid can be determined by the equation. (Where, P is density, V is volume, c is specific heat and A is area)
A. – 4 p v c = h a (t – t0)
B. – 3 p v c = h a (t – t0)
C. – 2 p v c = h a (t – t0)
D. – p v c = h a (t – t0)

Answer: D – p v c = h a (t – t0)
Explanation: it can be determined by relating rate of change of internal energy with conductive heat exchange at the surface.

217. Transient condition means
A. conduction when temperature at a point varies with time
B. very little heat transfer
C. heat transfer with a very little temperature difference
D. heat transfer for a short time

Answer: A conduction when temperature at a point varies with time
Explanation: the term transient or unsteady state designates a phenomenon which is time dependent.

218. Which of the following is not correct in a transient flow process?
A. the state of matter inside the control volume varies with time
B. there can be work and heat interactions across the control volume
C. there is no accumulation of energy inside the control volume
D. the rate of inflow and outflow of mass are different

Answer: C there is no accumulation of energy inside the control volume
Explanation: in transient heat conduction there is accumulation of energy inside the control volume.

219. The curve for unsteady state cooling or heating of bodies is
A. hyperbolic curve asymptotic both to time and temperature axis
B. exponential curve asymptotic both to time and temperature axis
C. parabolic curve asymptotic to time axis
D. exponential curve asymptotic to time axis

Answer: D exponential curve asymptotic to time axis
Explanation: α/α 0 = exponential [- h a t/p c v], which represents an exponential curve.

220. What is the wavelength band for TV rays?
A. 1 * 10 3 to 34 * 10 10 micron meter
B. 1 * 10 3 to 2 * 10 10 micron meter
C. 1 * 10 3 to 3 * 10 10 micron meter
D. 1 * 10 3 to 56 * 10 10 micron meter

Answer: B 1 * 10 3 to 2 * 10 10 micron meter
Explanation: this is the maximum and minimum wavelength for tv rays.

221. Thermal conductivity is defined as the heat flow per unit time
A. when the temperature gradient is unity
B. across the wall with no temperature
C. through a unit thickness of the wall
D. across unit area where the temperature gradient is unity

Answer: D across unit area where the temperature gradient is unity
Explanation: thermal conductivity of a material is because of migration of free electrons and lattice vibrational waves.

222. Mark the matter with least value of thermal conductivity
A. air
B. water
C. ash
D. window glass

Answer: A air
Explanation: for air, it is .024 w/ m degree

223. Which one of the following forms of water have the highest value of thermal conductivity?
A. boiling water
B. steam
C. solid ice
D. melting ice

Answer: C solid ice
Explanation: for ice, it is 2.25 w/m degree

224. The average thermal conductivities of water and air conform to the ratio
A. 50:1
B. 25:1
C. 5:1
D. 15:1

Answer: B 25:1
Explanation: for water, it is 0.55-0.7 w/m degree and for air it is .024 w/m degree.

225. Identify the very good insulator
A. saw dust
B. cork
C. asbestos sheet
D. glass wool

Answer: D glass wool
Explanation: glass wool has a lowest thermal conductivity of 0.03 w/m degree amongst given option.

226. Most metals are good conductor of heat because of
A. transport of energy
B. free electrons and frequent collision of atoms
C. lattice defects
D. capacity to absorb energy

Answer: B free electrons and frequent collision of atoms
Explanation: for good conductors, there must be electrons that are free to move.

227. Heat conduction in gases is due to
A. elastic impact of molecules
B. movement of electrons
C. em waves
D. mixing of gases

Answer: A elastic impact of molecules
Explanation: if there is elastic collision then after sometime molecules regain its natural position.

228. The heat energy propagation due to conduction heat transfer will be minimum for
A. lead
B. water
C. air
D. copper

Answer: C air
Explanation: it is because air has lowest

229. Cork is a good insulator because
A. it is flexible
B. it can be powdered
C. low density
D. it is porous

Answer: D it is porous
Explanation: cork has thermal conductivity in the range of 0.05-0.10 which is very low so it can be porous.

230. Choose the false statement
A. for pure metal thermal conductivity is more
B. thermal conductivity decreases with increase in the density of the substance
C. thermal conductivity of dry material is lower than that of damp material
D. heat treatment causes variation in thermal conductivity

Answer: B thermal conductivity decreases with increase in the density of the substance
Explanation: thermal conductivity increase with increase in the density of a substance.

231. A composite wall generally consists of
A. one homogenous layer
B. multiple heterogeneous layers
C. one heterogeneous layer
D. multiple homogenous layers

Answer: B multiple heterogeneous layers
Explanation: walls of houses where bricks are given a layer of plaster on either side.

232. Three metal walls of the same thickness and cross sectional area have thermal conductivities k, 2k and 3k respectively. The temperature drop across the walls (for same heat transfer) will be in the ratio
A. 3:2:1
B. 1:1:1
C. 1:2:3
D. given data is insufficient

Answer: A 3:2:1
Explanation: as, δ1 = δ2 = δ3 and cross sectional areas are same i.e. temperature drop varies inversely with thermal conductivity.

233. A composite wall is made of two layers of thickness δ1 and δ2 having thermal conductivities k and 2k and equal surface area normal to the direction of heat flow. The outer surface of composite wall are at 100 degree Celsius and 200 degree Celsius. The minimum surface temperature at the junction is 150 degree Celsius. What will be the ratio of wall thickness?
A. 1:1
B. 2:1
C. 1:2
D. 2:3

Answer: C 1:2
Explanation: q = k 1 a 1 d t 1 / δ1 = k 2 a 2 d t 2 / δ2 also areas are same.

234. A pipe carrying steam at 215.75 degree Celsius enters a room and some heat is gained by surrounding at 27.95 degree Celsius. The major effect of heat loss to surroundings will be due to
A. conduction
B. convection
C. radiation
D. both conduction and convection

Answer: C radiation
Explanation: as there is temperature difference so radiation suits well.

235. “Radiation cannot be affected through vacuum or space devoid of any matter”. True or false
A. true
B. false

Answer: B false
Explanation: it can be affected only by air between molecules and vacuum of any matter.

236. A composite wall of a furnace has two layers of equal thickness having thermal conductivities in the ratio 2:3. What is the ratio of the temperature drop across the two layers?
A. 2:3
B. 3:2
C. 1:2
D. log e 2 : log e 3

Answer: B 3:2
Explanation: we know that temperature is inversely proportional to thermal conductivity, so the ratio is 2:3.

237. According to Indian Standards, it is recommended that the overall thermal transmittance of a roof should not be more than kcal/m2 h deg C.
A. 2.00
B. 5.00
C. 7.00
D. 9.00

Answer: A 2.00
Explanation: according to indian standards, it is recommended that the overall thermal transmittance of a roof should not be more than 2.00 kcal/m2 h deg c. it is also recommended that the thermal dampness of a roof should be less than 75%.

238. The process of direct transmission of heat through a material is known as
A. conduction
B. radiation
C. thermal insulation
D. thermal energy

Answer: A conduction
Explanation: the process of direct transmission of heat through a material is known as conduction. the amount of heat transfer by this process depends on various factors like temperature difference, the conductivity of the medium, the time for which the flow takes place etc.

239. Thermal insulation keeps the room cool in winters and hot in summers.
A. true
B. false

Answer: B false
Explanation: thermal insulation keeps the room hot in winters and cool in summers which results in comfortable living. it minimises heat transfer and helps in saving

240. The amount of heat flow through a unit area of material of unit thickness in one hour, when the temperature difference is maintained at 1°C is known as of the material.
A. thermal conductivity
B. thermal resistivity
C. thermal conductance
D. thermal resistance

Answer: A thermal conductivity
Explanation: the amount of heat flow through a unit area of material of unit thickness in one hour, when the temperature difference is maintained at 1°c is known as the thermal conductivity. it is denoted by k. its units are w/(mk).

241. The reciprocal of thermal conductivity is known as
A. thermal conductance
B. surface resistance
C. specific conductance
D. thermal resistivity

Answer: D thermal resistivity
Explanation: the reciprocal of thermal conductivity is known as thermal resistivity. it is given by 1/k. its units are (mk)/w.

242. Which of the following is the correct relationship between thermal resistance and thermal conductivity?
A. r = k/l
B. r = k.l
C. r = l/k
D. r = l2/k

Answer: C r = l/k
Explanation: thermal resistance and thermal conductivity are related by the equation r = l/k. here, r is the thermal resistance, k is the thermal conductivity and l is the thickness. thermal resistance is the reciprocal of thermal conductance.

243. Surface resistance is the reciprocal of
A. surface coefficient
B. surface resistivity
C. surface conductance
D. surface conductivity

Answer: A surface coefficient
Explanation: surface resistance is the reciprocal of the surface coefficient. it is given by 1/f where f denotes the surface coefficient. its units are (m2k)/w.

244. Thermal damping is given by the equation D = (T-t/T) x 100. Here, T denotes
A. outside temperature range
B. inside temperature range
C. total outside and inside temperature range
D. thickness

Answer: A outside temperature range
Explanation: thermal damping is given by the equation d = (t-t/t) x 100. here, t denotes outside temperature range and t denotes inside temperature range. also, thermal damping is denoted by d.

245. Which of the following is the correct relation between thermal transmittance and thermal time constant?
A. t = q x u
B. t = k/u
C. t = q/u
D. t = u/q

Answer: C t = q/u
Explanation: thermal transmittance and thermal time constant are related by the equation t = q/u. here, t denotes the thermal time constant, u is the thermal transmittance and q is the quantity of heat stored.

246. Which of the following is not a quality of a good thermal insulating material?
A. it should be durable
B. it should have a low thermal resistance
C. it should be readily available
D. it should be fireproof

Answer: B it should have a low thermal resistance
Explanation: a good thermal insulating material should be durable. it should have high thermal resistance. it should be fireproof and readily available.

247. Reflective sheet materials used as thermal insulating material have reflectivity and emissivity.
A. high, high
B. high, low
C. low, low
D. low, high

Answer: B high, low
Explanation: reflective sheet materials used as thermal insulating material have high reflectivity and low emissivity. because of this property, it offers high heat resistance.

248. Thermal insulation of roofs can be obtained by covering the top exposed surface of the roof with
A. 2.5 cm thick layer of mud mortar
B. 2.5 cm thick layer of coconut pitch cement concrete
C. 7.5 cm thick layer of mud mortar
D. 7.5 m thick layer of coconut pitch cement concrete

Answer: B 2.5 cm thick layer of coconut pitch cement concrete
Explanation: thermal insulation of roofs can be obtained by covering the top exposed surface of the roof with 2.5 cm thick layer of coconut pitch cement concrete. coconut pitch cement concrete is prepared by mixing coconut pitch with water and cement.

249. Presence of moisture in the thermal insulating material increases thermal insulation while the presence of air spaces decreases thermal insulation.
A. true
B. false

Answer: B false
Explanation: presence of moisture in the thermal insulating material decreases thermal insulation while the presence of air spaces increases thermal insulation. the choice of the thermal insulating material depends on various factors like cost of material, area to be covered, coat of heating or cooling, etc.

250. According to the Indian Standards, it is recommended that thermal damping of a wall should not be less than
A. 40%
B. 50%
C. 60%
D. 80%

Answer: C 60%
Explanation: according to the indian standards, it is recommended that the thermal damping of a wall should not be less than 60%. hence, it is also recommended that the thermal time constant should not be less than 16 h.

276. The energy emitted by a black surface should not vary in accordance with
A. wavelength
B. temperature
C. surface characteristics
D. time

Answer: D time
Explanation: it is time independent. for a prescribed wavelength, the body radiates much more energy at elevated temperatures.

277. 2 PLANCK’S THEORY (DERIVATION)
A. a sin α
B. a cos α
C. 2a cos α
D. 2a cos α

Answer: B a cos α
Explanation: the solid angle is defined by a region by the rays of a sphere, and is measured as a n/r2.

278. Likewise the amount of emitted radiation is strongly influenced by the wavelength even if temperature of the body is
A. constant
B. increasing
C. decreasing
D. it is not related with temperature

Answer: A constant
Explanation: temperature must remain constant in order to emit radiation.

279. 5 kW/m2. Determine the wavelength of emission maximum
A. 8.46 micron m
B. 7.46 micron m
C. 6.46 micron m
D. 5.46 micron m

Answer: D 5.46 micron m
Explanation: (wavelength) max t = 2.8908 * 10 -3.

280. The sun emits maximum radiation of 0.52 micron meter. Assuming the sun to be a black body, Calculate the emissive ability of the sun’s surface at that temperature
A. 3.47 * 10 7 w/m2
B. 4.47 * 10 7 w/m2
C. 5.47 * 10 7 w/m2
D. 6.47 * 10 7 w/m2

Answer: C 5.47 * 10 7 w/m2
Explanation: e = σ b t 4 = 5.47 * 10 7 w/m2.

281. The law governing the distribution of radiant energy over wavelength for a black body at fixed temperature is referred to as
A. kirchhoff’s law
B. planck’s law
C. wein’s formula
D. lambert’s law

Answer: B planck’s law
Explanation: this law gives a relation between energy over wavelength.

282. The Planck’s constant h has the dimensions equal to
A. m l 2 t -1
B. m l t -1
C. m l t -2
D. m l t

Answer: A m l 2 t -1
Explanation: it has unit equal to j s and its value is 6.626 * 10 -34.

283. A furnace emits radiation at 2000 K. Treating it as a black body radiation, calculate the monochromatic radiant flux density at 1 micron m wavelength
A. 5.81 * 10 7 w/m2
B. 4.81 * 10 7 w/m2
C. 3.81 * 10 7 w/m2
D. 2.81 * 10 7 w/m2

Answer: D 2.81 * 10 7 w/m2
Explanation: (e) b = c 1 (wavelength)

284. A metal sphere of surface area 0.0225 m2 is in an evacuated enclosure whose walls are held at a very low temperature. Electric current is passed through resistors embedded in the sphere causing electrical energy to be dissipated at the rate of 75 W. If the sphere surfaces temperature is measured to be 560 K, while in steady state, calculate emissivity of the sphere surface
A. 0.498
B. 0.598
C. 0.698
D. 0.798

Answer: B 0.598
Explanation: e = e a σ b t.

285. Which of the following is the characteristic of a black body?
A. a perfect absorber but an imperfect radiator
B. a perfect radiator but an imperfect absorber
C. a perfect radiator and a perfect absorber
D. a perfect conductor

Answer: C a perfect radiator and a perfect absorber
Explanation: when the radiations are made

286. The energy distribution is not uniform for any given temperature in a perfect black body.
A. true
B. false

Answer: A true
Explanation: at different temperatures, when a perfect black body is allowed to emit radiations, then the distribution of energy for different wavelengths at various temperatures is not uniform.

287. Rayleigh-Jean’s law holds good for which of the following?
A. shorter wavelength
B. longer wavelength
C. high temperature
D. high energy

Answer: B longer wavelength
Explanation: according to this law, the energy distribution is directly proportional to the absolute temperature and is inversely proportional to the fourth power of the wavelength. therefore longer the wavelength, greater is the energy distribution.

288. Wien’s displacement law holds good only for shorter wavelength.
A. false
B. true

Answer: B true
Explanation: this law states that, the product of the wavelength, corresponding to maximum energy and the absolute temperature, is constant. if ʎ is less, then 1/ʎ will be great. therefore e(hc/ʎkt) will be great.

289. Which of the following does not affect the photon?
A. magnetic or electric field
B. light waves
C. gravity
D. current

Answer: A magnetic or electric field
Explanation: photons have no charge. they can interact with charged particles but not with themselves. this is why photons are neutral and not affected by magnetic or electric fields.

290. What is Compton shift?
A. shift in frequency
B. shift in charges
C. shift in radiation
D. shift in wavelength

Answer: D shift in wavelength
Explanation: when a photon collides with an electron at rest, the photon gives its energy to the electron. therefore the scattered photon will have higher wavelength compared to the wavelength of the incident photon. this shift in wavelength is called compton shift.

291. Compton shift depends on which of the following?
A. incident radiation
B. nature of scattering substance
C. angle of scattering
D. amplitude of frequency

Answer: C angle of scattering
Explanation: from the theory of compton effect it is deducted that change in wavelength

292. Which of the following is called as non- mechanical waves?
A. magnetic waves
B. electromagnetic waves
C. electrical waves
D. matter waves

Answer: B electromagnetic waves
Explanation: the waves which travel in the form of oscillating electric and magnetic waves are called electromagnetic waves. such waves do not require any material for their propagation and are called non-mechanical waves.

293. Which of the following is associated with an electron microscope?
A. matter waves
B. electrical waves
C. magnetic waves
D. electromagnetic waves

Answer: A matter waves
Explanation: the waves associated with microscopic particles when they are in motion are called matter waves. electron microscope makes use of the matter waves associated with fast moving electrons.

294. A radio station broadcasts its programme at 219.3 metre wavelength. Determine the frequency of radio waves if velocity of radio waves is 3×108 m/s.
A. 7.31×10-7 hz
B. 1.954×10-6 hz
C. 1.368×106 hz
D. 6.579×1010 hz

Answer: C 1.368×106 hz
Explanation: ʎ = velocity/frequency frequency = velocity/ʎ

295. Calculate the de-Broglie wavelength of an electron which has been accelerated from rest on application of potential of 400volts.
A. 0.1653 Å
B. 0.5125 Å
C. 0.6135 Å
D. 0.2514 Å

Answer: C 0.6135 Å
Explanation: de-broglie wavelength = h/

296. When a pebble is dropped into a pond of still water, what happens?
A. particles move
B. waves move
C. the pebble moves
D. water moves

Answer: B waves move
Explanation: when a pebble is thrown in still water, a circular pattern of alternate crests spread out. the kinetic energy makes the particles to oscillate which comes in contact with it. the energy gets transferred to the particles of the next layer which also begins to oscillate. thus it is the disturbance or waves that move forward and not the particles of the medium.

297. Mechanical waves are called elastic waves.
A. true
B. false

Answer: A true
Explanation: waves which require a medium for their propagation are called mechanical waves. they are also called elastic waves because they depend on the elastic properties of a medium.

298. What are the essential properties a medium must possess for the propagation of mechanical waves?
A. stable pressure
B. maximum friction
C. constant temperature
D. minimum friction

Answer: D minimum friction
Explanation: the friction force amongst the particles of the medium should be negligibly small so that they continue oscillating for a sufficiently long time and the wave travels a sufficiently long distance through the medium

299. Transverse waves can be formed in fluids.
A. true
B. false

Answer: B false
Explanation: transverse waves travel in the form of crests and troughs. they involve changes in the shape of the medium. so they can be transmitted through media which have rigidity. as fluids do not sustain shearing stress, transverse waves cannot be formed in them.

300. Which of the following waves can be transmitted through solids, liquids and gases?
A. transverse waves
B. electromagnetic waves
C. mechanical waves
D. longitudinal waves

Answer: D longitudinal waves
Explanation: longitudinal waves involve changes in the volume and density of the medium. since all media can sustain compressive stress, longitudinal waves can be transmitted through all the three types of media.

301. For an aluminium the modulus of rigidity is 2.1×1010 N/m2 and density is 2.7×103 kg/m3. Find the speed of transverse waves in the medium.
A. 27.9×103 m/s
B. 2.79×103 m/s
C. 25.14×103 m/s
D. 24.1×103 m/s

Answer: B 2.79×103 m/s
Explanation: speed = √(Ƞ/ƿ) speed = 2.79×103 m/s.

302. Sound travels through a gas under which of the following condition?
A. isothermal condition
B. non-isothermal condition
C. adiabatic condition
D. transverse condition

Answer: C adiabatic condition
Explanation: the compressions and rarefactions are formed so rapidly that the heat generated in the regions of compressions does not get time to pass into the regions of rarefactions so as to equalize the temperature. so when sound travels through gas, the temperature remains constant. therefore, it is adiabatic.

303. What kind of wave is formed in organ pipes?
A. transverse stationary waves
B. electromagnetic waves
C. mechanical waves
D. longitudinal stationary waves

Answer: D longitudinal stationary waves
Explanation: when two identical longitudinal waves travelling in opposite directions overlap, a longitudinal stationary wave is formed. thus, the waves produced in organ pipes are longitudinal stationary waves.

304. A wave transmits momentum. Can’t it transfer angular momentum?
A. yes
B. no

Answer: B no
Explanation: a wave transmitting momentum cannot transmit angular momentum because a transfer of angular momentum means the action of a torque which causes rotator motion.

305. What is the most fundamental property of wave?
A. temperature
B. pressure
C. frequency
D. wavelength

Answer: C frequency
Explanation: when a wave travels from one medium to other, its wavelength as well as velocity may change. this is the reason that frequency is the fundamental property of a wave.

306. Which of the following is also known as pressure waves?
A. transverse waves
B. longitudinal waves
C. mechanical waves
D. stationary waves

Answer: B longitudinal waves
Explanation: longitudinal waves travel in a medium as series of alternate compressions and rarefactions and hence are called pressure waves.

307. In which medium sound travels faster?
A. solid
B. liquid
C. gas
D. water vapour

Answer: A solid
Explanation: sound travels in solid with the highest speed because the coefficient of elasticity of solids is much greater than the coefficient of elasticity of liquids and gases.

308. TEM and SEM are the same microscopy techniques.
A. true
B. false

Answer: A true
Explanation: transmission electron microscopy (tem) and scanning electron microscopy (sem) are the different types of

309. The resolving power of TEM is derived from
A. electrons
B. specimens
C. power
D. ocular system

Answer: A electrons
Explanation: the resolving power of a transmission electron microscope is derived from the wave-like property of electrons that pass through the specimen. in sem, the electrons reflect back from the specimen.

310. The cathode of transmission electron microscope consists of a
A. tungsten wire
B. bulb
C. iron filament
D. gold wire

Answer: A tungsten wire
Explanation: the cathode of a transmission electron microscope (tem) is located on top of the column, it contains a tungsten wire filament that is heated to provide the source of electrons.

311. The resolution attainable with standard TEM is less than the theoretical value.
A. true
B. false

Answer: A true
Explanation: the resolution that can be attained with a standard transmission electron microscope is about two orders of magnitude less than the theoretical value. this is due to spherical aberration of electron-focusing lenses.

312. During TEM, a vacuum is created inside the
A. room of operation
B. specimen
C. column
D. ocular system

Answer: C column
Explanation: to prevent the premature scattering of electrons by collision with the gas molecules, a vacuum is generated through which the electrons travel, in the column prior to operation.

313. Which of the following component of TEM focuses the beam of electrons on the sample?
A. ocular lens
B. condenser lens
C. stage
D. column

Answer: B condenser lens
Explanation: the condenser lens focuses the electron beam on to the specimen, in case of transmission electron microscope. the specimen is supported on the grid holder and placed inside the column.

314. Image formation in electron microscope is based on
A. column length
B. electron number
C. differential scattering
D. specimen size

Answer: C differential scattering
Explanation: in case of the electron microscope, the image formation is based on the differential scattering of the electrons by parts of the specimen. the scattering of electrons is proportional to the size nuclei of the atoms that make up the sample.

315. The biological materials have little intrinsic capability to
A. scatter electrons
B. stain
C. remain viable
D. be captured

Answer: A scatter electrons
Explanation: the insoluble materials of cells contain atoms of low atomic number such as carbon, hydrogen, oxygen and nitrogen. the biological materials therefore have very little intrinsic capability of scattering the electrons.

316. Glutaraldehyde is a
A. metal
B. fixative
C. non-metal
D. atomic species

Answer: B fixative
Explanation: glutaraldehyde and osmium tetroxide are common fixatives used in the transmission electron microscopy for the fixation of biological specimens. they stain as well as keep the sectioned specimens in a state of similarity with the living counterpart.

317. Osmium is a
A. non metal
B. heavy metal
C. alloy
D. light metal

Answer: B heavy metal
Explanation: osmium is a heavy metal that reacts with fatty acids leading to the preservation of membranes. osmium tetroxide is used as a fixative in transmission

318. Shadow casting is a technique of visualizing
A. isolated particles
B. mounts
C. shoot tips
D. root tips

Answer: A isolated particles
Explanation: shadow casting is a technique of viewing isolated particles. the particles are made to cast shadows after their placement in sealed chambers. the chamber contains a filament of carbon and a heavy metal.

319. Which of the following can be a wave function?
A. tan x
B. sin x
C. cot x
D. sec x

Answer: B sin x
Explanation: out of all the given options, sin x is the only function, that is continuous and single-valued. all the rest of the functions are either discontinuous or double-valued.

320. Which of the following is not a characteristic of wave function?
A. continuous
B. single valued
C. differentiable
D. physically significant

Answer: D physically significant
Explanation: the wave function has no physical significance. it merely helps in determining the state of a particle. it is the square of the wave function that has a physical significance.

321. dΨ/dx must be zero.
A. true
B. false

Answer: B false
Explanation: for a wave function, dΨ/dx, must be continuous and single-valued everywhere, just like Ψ. also, Ψ must be normalizable.

322. Any wave function can be written as a linear combination of
A. eigen vectors
B. eigen values
C. eigen functions
D. operators

Answer: C eigen functions
Explanation: a wave function describes the state of a particle. it does not have a physical significance. moreover, it can be written as a linear combination of eigen functions, i.e., Ψ(x) = af(x) + bg(x).

323. The Schrödinger is a differential equation.
A. true
B. false

Answer: B false
Explanation: the schrodinger wave equation

  250+ TOP MCQs on Work Done and Answers

324. The walls of a particle in a box are supposed to be
A. small but infinitely hard
B. infinitely large but soft
C. soft and small
D. infinitely hard and infinitely large

Answer: D infinitely hard and infinitely large
Explanation: the simplest quantum- mechanical problem is that of a particle in a box with infinitely hard walls and are infinitely large.

325. The wave function of the particle lies in which region?
A. x > 0
B. x < 0
C. 0 < x < l D. x > l

Answer: C 0 < x < l
Explanation: the particle cannot exist outside the box, as it cannot have infinite amount of energy. thus, it’s wave function is between 0 and l, where l is the length of the side of the box.

326. The particle loses energy when it collides with the wall.
A. true
B. false

Answer: B false
Explanation: the total energy of the particle inside the box remains constant. it does not loses energy when it collides with the wall.

327. The Energy of the particle is proportional to
A. n
B. n-1
C. n2
D. n-2

Answer: C n2
Explanation: in a particle inside a box, the energy of the particle is directly proportional to the square of the quantum state in which the particle currently is.

328. For a particle inside a box, the potential is maximum at x =
A. l
B. 2l
C. l/2
D. 3l

Answer: A l
Explanation: in a box with infinitely high barriers with infinitely hard walls, the potential is infinite when x = 0 and when x = l.

329. The Eigen value of a particle in a box is
A. l/2
B. 2/l
C. √l/2
D. √2/l

Answer: D √2/l
Explanation: the wave function for the particle in a box is normalizable, when the value of the coefficient of sin is equal to

330. Particle in a box can never be at rest.
A. true
B. false

Answer: A true
Explanation: if the particle in a box has zero energy, it will be at rest inside the well and it violates the heisenberg’s uncertainty principle. thus, the minimum energy possessed by a particle is not equal to zero.

331. The wave function for which quantum state is shown in the figure?
A. 1
B. 2
C. 3
D. 4

Answer: B 2
Explanation: the shown wave function is for the 2nd principal quantum number, i.e., it is the wave function for the state when n = 2.

332. The line at which the tunnel wall breaks from sloping outward can be given as
A. spring line
B. oval line
C. centre line
D. middle line

Answer: A spring line
Explanation: spring line is determined as the line at which the wall breaks from sloping outward to sloping inward toward the crown.

333. Which of the following should be considered while aligning a tunnel?
A. atmospheric conditions
B. hydrological conditions
C. climatic conditions
D. surface limits

Answer: B hydrological conditions
Explanation: the determination of the alignment for tunnel can be done based on geological and hydrological conditions, cross- section and length of the continuous tunnel, time of consideration and limit of the surface.

334. Among the following, which doesn’t belong to tunnel classification?
A. firm ground
B. running ground
C. rocky ground
D. soft ground

Answer: C rocky ground
Explanation: tunneling has been classified based on the type of strata present. it includes firm ground, soft ground and running ground. these will determine the bearing capacity of the soil.

335. Which method can be adopted if full face excavation is not possible?
A. back bearing method
B. plotting
C. trenching
D. benching

Answer: D benching
Explanation: in case of no possibility of full face excavation, top heading method is adopted for having a better output. benching process is also adopted for digging small tunnels.

336. Among the following, which can be adopted for providing support for soft strata?
A. bents of aluminum
B. bents of iridium
C. bents of steel
D. bents of plastic

Answer: C bents of steel
Explanation: the provision of soft strata must be done for withstanding the excavation. it can be provided by bents of wood, bents of steel, liner plates and poling, which are placed to retain material between the adjacent bents.

337. A steel cylinder which is pushed in the soft soil is determined as
A. jar born
B. shield
C. rod
D. pole

Answer: B shield
Explanation: in the case of soft grounds, tunneling can be dangerous and cave-ins are common. to prevent this, an iron or steel cylindrical element called shield is placed in the soft soil, which can crave the hole perfectly.

338. Which method can be adopted in case of rock tunneling?
A. full face method
B. benching
C. tracing
D. back bearing method

Answer: A full face method
Explanation: rock tunneling involves the same principle as of the tunneling in the ground. those include full face method, top heading method and drift method. based on the conditions of the area, these can be adopted.

339. Which of the following can act as an alternative for blasting?
A. tunneling
B. continuous blasting
C. sequential blasting
D. fire-setting

Answer: D fire-setting
Explanation: blasting is the conventional method which is adopted in case of rock tunneling. in the case of fire-setting, tunnel is heated with fire and then cooled with water. rapid expansion and contraction weakens and rock and tends to break.

340. Which of the following involves in the sequence of rocky strata?
A. marking profile
B. placing rocks
C. improving foul gases
D. recording values

Answer: A marking profile
Explanation: rocky strata involve usage of blasting method for developing tunnels. the sequence contains marking profile, loading explosive, removing foul gases, checking, scaling, mucking and bolting.

341. Which of the following are true for electron microscopy?
A. specimen should be thin and dry
B. image is obtained on a phosphorescent screen
C. electron beam must pass through evacuated chamber
D. specimen should be thin and dry, image is obtained on a phosphorescent screen and electron beam must pass through evacuated chamber

Answer: D specimen should be thin and dry, image is obtained on a phosphorescent screen and electron beam must pass through evacuated chamber
Explanation: since electrons can travel only in high vacuum, the entire electron path through the instrument must be evacuated; specimens must be completely dehydrated prior to examination. only very thin specimens can be observed in the conventional electron microscope since the penetrating power of electrons through matter is weak. the magnified image may be viewed on a phosphorescent or fluorescent screen.

342. Negative Staining is used for examining
A. virus particles
B. protein molecules
C. bacterial flagella
D. virus particles, protein molecules and bacterial flagella

Answer: D virus particles, protein molecules and bacterial flagella
Explanation: in negative-staining the electron opacity of the surrounding field is increased by using an electron-dense material such as phosphotungstic acid as a stain.

343. Which among the following helps us in getting a three-dimensional picture of the specimen?
A. transmission electron microscope
B. scanning electron microscope
C. compound microscope
D. simple microscope

Answer: B scanning electron microscope
Explanation: the scanning electron microscope lacks the resolving power obtainable with the transmission electron microscope but has the advantage of revealing a striking three-dimensional picture. the surface topography of a specimen can be revealed with clarity and depth of field not possible by any other method.

344. The secondary electrons radiated back in scanning microscope is collected by?
A. specimen
B. anode
C. vacuum chamber
D. cathode

Answer: B anode
Explanation: in scanning electron

345. On what factors do the intensity of secondary electrons depend upon?
A. shape of the irradiated object
B. chemical composition of the irradiated object
C. number of electrons ejected
D. size and chemical composition of the irradiated object, number of electrons ejected and on the number of electrons reabsorbed by surrounding

Answer: D size and chemical composition of the irradiated object, number of electrons ejected and on the number of electrons reabsorbed by surrounding
Explanation: the irradiations in sem causes secondary electrons to be ejected from the specimen thereby generating a signal that is proportional to the number of electrons striking the anode. the intensity or the number of secondary electrons depends on the shape and the chemical composition of the irradiated object and also on the number of electrons ejected and the number of electrons reabsorbed by surrounding.

346. Where do we obtain the magnified image of the specimen in SEM?
A. cathode ray tube
B. phosphorescent screen
C. anode
D. scanning generator

Answer: A cathode ray tube
Explanation: in tem, the image is obtained on a phosphorescent screen but in sem the magnified image of the surface topography of the specimen is obtained on the cathode ray tube. the electronic signals generated scan the specimen in a raster pattern in the manner of a television system to produce an image on a cathode ray tube.

347. Which of the following techniques are used in Transmission Electron Microscopy (TEM) for examining cellular structure?
A. negative-staining
B. shadow casting
C. ultrathin sectioning
D. negative-staining, shadow casting, ultrathin sectioning, freeze-etching

Answer: D negative-staining, shadow casting, ultrathin sectioning, freeze-etching
Explanation: numerous techniques are available for use with electron microscopy which extends its usefulness in characterizing cellular structure. some of them are

348. Which of the following properties is generally exhibited by amorphous solids?
A. anisotropy
B. glass-transition
C. equal strength of all bonds
D. all of the mentioned

Answer: B glass-transition
Explanation: due to random organization of particles, amorphous solids have the same physical properties along all directions, or are isotropic. random organization of particles also results in unequal bond strengths. upon cooling, amorphous solids turn into a brittle

349. Metal glass was first prepared at:
A. california institute of technology
B. massachusetts institute of technology
C. technion
D. university of michigan

Answer: A california institute of technology
Explanation: metal glass or amorphous metal was reportedly first produced by w. klement (jr.), willens and duwez in 1960 at caltech. it was prepared by rapid cooling (~ 1 mk/s) of molten metal alloys.

350. Polycrystalline solids are isotropic.
A. true
B. false

Answer: A true
Explanation: anisotropy is a characteristic behavior shown by ideal crystals. however,

351. Metal glasses differ from their crystalline counterparts in many ways. Chief application(s) of metal glasses include(s):
A. bullet-proof glasses
B. power transformers
C. conducting wires
D. all of the mentioned

Answer: B power transformers
Explanation: amorphous metals are not transparent and have relatively lower electrical conductivity. however, most metal glasses possess high magnetic susceptibility and low coercivity.

352. Soda-lime glass is the most common type of glass. The component present in largest w/w percentage is:
A. sio2
B. al2o3
C. na2o
D. cao

Answer: A sio2
Explanation: glass inherits its transparency from crystalline sio2, also called quartz.

353. Lead-oxide glass is called “crystal glass” because:
A. it contains crystalline pb
B. it contains sio2 crystals
C. it contains pbo crystals
D. none of the mentioned

Answer: D none of the mentioned
Explanation: well, crystal glass is amorphous, not crystalline. this glass earns its name from its excellent decorative properties and high refractive index.

354. Crystallinity increases with increasing rate of cooling of a liquid.
A. true
B. false

Answer: B false
Explanation: when a liquid is cooled rapidly, the particles get less time to move and arrange themselves in an orderly fashion and hence the crystallinity of the resulting solid decreases.

355. 2 SINGLE CRYSTALS: UNIT CELL, CRYSTAL SYSTEMS, BRAVAIS LATTICES, DIRECTIONS AND PLANES IN A CRYSTAL, MILLER INDICES
A. unit cell edge lengths
B. distance between nearest neighbours
C. cosine of angles between unit cell edges
D. none of the mentioned view answer

Answer: A unit cell edge lengths
Explanation: point coordinate indices are the fractions which when multiplied by the corresponding unit cell edge lengths, provide the location of a given point in the crystallographic coordinate system.

356. In cubic crystals, crystallographic directions are arranged in families. Which of the following directions does not belong to the family <110>?
A. [1 0 1]
B. [11 0]
C. [10 1̅]
D. none of the mentioned view answer

Answer: D none of the mentioned view answer
Explanation: since the cubic lattice is symmetrical about all the three axes, the above directions are equivalent irrespective of order & sign and are part of same direction family.

357. Which of the following is a property of Miller indices?
A. they uniquely identify a plane
B. they are always positive
C. they are not fractions
D. none of the mentioned view answer

Answer: C they are not fractions
Explanation: two or more planes can have same miller indices which can be negative, zero or positive depending on the intercept on the axes. if the ratios of intercepts to lattice constants come out be fractional, then they are scaled to lowest integers to be represented as miller indices.

358. Miller indices for perpendicular planes are always the same.
A. true
B. false view answer

Answer: B false view answer
Explanation: it is true only for cubic lattices. for other systems, there is no simple relationship between planes with the same miller indices.

359. For destructive interference to take place, the path difference between the two waves should be:
A. nλ
B. 2nλ
C. (n + 1/2)λ
D. (2n + 1)λ

Answer: A nλ
Explanation: constructive interference occurs when the phase difference between two interfering waves is an integral multiple of 2π. also, the ratio of path difference to wavelength equals that of phase difference to 2π.

360. Bragg’s law is not a sufficient condition for diffraction by crystalline solids.
A. true
B. false view answer

Answer: A true
Explanation: atoms present at non-corner positions may result in out-of-phase scattering at bragg angles.

361. The Miller indices h, k, and l of parallel planes in a BCC lattice should satisfy which of the following X-ray diffraction reflection rules?
A. h + k + l should be even
B. h, k, and l should all be either even or odd
C. h, k, and l should form pythagoras triplet
D. all planes allow reflections view answer

Answer: A h + k + l should be even
Explanation: if the sum of miller indices becomes odd for a bcc lattice, destructive interference occurs.

362. Laue’s model pictures XRD as reflection from parallel crystalline planes. Reflection is different from refraction as:
A. diffraction occurs throughout the bulk
B. intensity of diffracted beams is less
C. diffraction in crystals occurs only at bragg’s angles
D. all of the mentioned view answer

Answer: D all of the mentioned view answer
Explanation: reflection is a surface

363. K-alpha x-rays have shorter wavelengths than K-beta x-rays?
A. true
B. false view answer

Answer: B false view answer
Explanation: k-alpha is formed from a transfer of electrons from l shell to k while k-beta result from m-to-k transition. hence k-alpha lines have lower energy (or longer wavelength).

364. Which of the following has a HCP crystal structure?
A. w
B. mo
C. cr
D. zr

Answer: D zr
Explanation: crystalline solids are classified

365. Amorphous solids have structure.
A. regular
B. linear
C. irregular
D. dendritic

Answer: C irregular
Explanation: materials in which the molecule is the basic structural solid and has an irregular structure is known as amorphous solid. crystalline solids, on the other hand, usually are arranged in a regular manner.

366. At iron changes its BCC structure to FCC.
A. 308oc
B. 568oc
C. 771oc
D. 906oc

Answer: D 906oc
Explanation: similar to metallic crystals, a few non-metallic crystals also change form due to temperature and pressure differences. this process is termed as polymorphism. iron changes from bcc at room temperature to fcc form at 906oc.

367. At room temperature, tin is formed into
A. gray tin
B. white tin
C. red tin
D. yellow tin

Answer: B white tin
Explanation: similar to metallic crystals, a few non-metallic crystals also change form due to temperature and pressure differences. tin crystallizes in a non-metallic diamond structure (gray tin) at low temperatures. at

368. Which of the following is a property of non-metallic crystals?
A. highly ductile
B. less brittle
C. low electrical conductivity
D. fcc structure

Answer: C low electrical conductivity
Explanation: non-metallic crystals are less ductile and have low electrical conductivity. on the other hand, metallic crystals are differing since they are more ductile and have high electrical conductivity.

369. Which of the following is not an amorphous material?
A. glass
B. plastics
C. lead
D. rubbers

Answer: C lead
Explanation: materials in which the molecule is the basic structural solid and has an irregular structure are known as amorphous solid. most amorphous materials are polymers such as plastics and rubbers.

370. The smallest portion of the lattice is known as
A. lattice structure
B. lattice point
C. bravais crystal
D. unit cell

Answer: D unit cell
Explanation: lattice is defined as the regular geometrical arrangement of points in crystal space. the unit cell is the smallest portion of the lattice, which when repeated in all directions gives rise to a lattice structure.

371. A unit cell that contains lattice points only at the corners is known as
A. primitive unit cell
B. secondary unit cell
C. layered unit cell
D. derived unit cell

Answer: A primitive unit cell
Explanation: if a unit cell chosen contains lattice points only at its corners, it is called a primitive or simple unit cell. it contains only one lattice point since each point at the eight corners is shared equally with adjacent unit cells.

372. The axial relationship of a monoclinic crystal system is given as
A. a = b = c
B. a = b ≠ c
C. a ≠ b = c
D. a ≠ b ≠ c

Answer: D a ≠ b ≠ c
Explanation: the crystal system is a format by which crystal structures are classified.

373. The axial relationship of a rhombohedral crystal system is given as
A. a = b = c
B. a = b ≠ c
C. a ≠ b = c
D. a ≠ b ≠ c

Answer: A a = b = c
Explanation: the crystal system is a format by which crystal structures are classified.

374. The interracial angles of a hexagonal crystal system are given by
A. α = β = ϒ = 90o
B. α = β = 90o ϒ = 120o
C. α = β = ϒ ≠ 90o
D. α ≠ β ≠ ϒ ≠ 90o

Answer: B α = β = 90o ϒ = 120o
Explanation: the crystal system is a system by which crystal structures are classified.

375. The interracial angles of a triclinic crystal system are given by
A. α = β = ϒ = 90o
B. α = β = 90o ϒ = 120o
C. α = β = ϒ ≠ 90o
D. α ≠ β ≠ ϒ ≠ 90o

Answer: D α ≠ β ≠ ϒ ≠ 90o
Explanation: the crystal system is a system by which crystal structures are classified.

376. What is the atomic radius of a BCC crystal structure?
A. a/2
B. a/4
C. a√2/4
D. a√3/4

Answer: D a√3/4
Explanation: atomic radius is defined as half the distance between the centers of two neighboring atoms. the atomic radius of a simple cube and hcp is a/2 respectively, whereas it is a√2/4 and a√3/4 for fcc and bcc respectively.

377. What is the coordination number of a simple cubic structure?
A. 6
B. 8
C. 10
D. 12

Answer: A 6
Explanation: coordination number is defined as the number of nearest neighboring atoms in crystals. the coordination number for the simple cubic structure is 6, whereas it is 8 and 12 for bcc and fcc respectively.

378. What is the atomic packing factor of BCC structure?
A. 0.54
B. 0.68
C. 0.74
D. 0.96

Answer: B 0.68
Explanation: the density of packing in a crystal is determined using the atomic packing factor (apf). the apf of fcc and hcp structures is 0.74, and 0.54 for simple cubic structure, whereas it is 0.68 for bcc structure.

379. Which of the following is a point defect in crystals?
A. edge dislocation
B. interstitialcies
C. grain boundaries
D. cracks

Answer: B interstitialcies
Explanation: crystal defects are classified as point defects, line defects, and boundary defects. point defects include vacancies, impurities, interstitialcies, and electronic defects.

380. The defect that occurs due to a displacement of an ion is known as
A. vacancy defect
B. schottky defect
C. frankel defect
D. interstitial defect

Answer: C frankel defect
Explanation: frankel defect occurs due to a displacement of an ion from the crystal lattice. it is related to the interstitial defect, where an ion simply occupies a position between regular atoms.

381. Which defect does the following figure depict?
A. vacancy defect
B. schottky defect
C. frankel defect
D. interstitial defect

Answer: B schottky defect
Explanation: when a pair of positive and negative ions both disappear from a crystal lattice, the effect is called a schottky defect. it is closely related to vacancy defects where simply an ion is missing.

382. Which defect does the following diagram represent?
A. vacancy defect
B. schottky defect
C. frankel defect
D. interstitial defect

Answer: D interstitial defect
Explanation: interstitial defects occur when an atom occupies an empty position in a crystal lattice. self-interstitial effects occur due to their own atoms, while others occur due to a foreign substance.

383. occurs when a foreign substance replaces an atom in a crystal.
A. vacancy defect
B. substitutional impurity
C. frankel defect
D. interstitial impurity

Answer: B substitutional impurity
Explanation: a substitutional impurity occurs due to the occupation of a foreign atom in place of an atom in a crystal. on the other hand, interstitial impurities occur when a regular atom occupies a random space in the crystal lattice.

384. A disturbance in a region between two ideal parts of a crystal is known as
A. boundary defect
B. point defect
C. line defect
D. volume defect

Answer: C line defect
Explanation: line defect is regarded as a disturbed region between two perfect parts of a crystal. they may be of either edge dislocation type or screw dislocation.

385. In screw dislocation, the Burger’s vector lies to the dislocation line.
A. perpendicular
B. parallel
C. at an angle
D. sideways

Answer: B parallel
Explanation: the burger’s vector in screw dislocation lies parallel to the dislocation line along the axis of a line of atoms in the same plane. on the other hand, it lies at an angle for edge dislocation.

386. Generation of dislocations can be identified using
A. schottky mechanism
B. burger’s vector
C. twist
D. frank-read mechanism

Answer: D frank-read mechanism
Explanation: the frank-read mechanism

387. What are one-dimensional defects?
A. boundary defect
B. point defect
C. line defect
D. volume defect

Answer: C line defect
Explanation: when compared geometrically, line defects are seen as one-dimensional defects. line defects are also known as dislocations, with common types as edge and screw dislocations.

388. What are two-dimensional defects?
A. boundary defect
B. point defect
C. line defect
D. volume defect

Answer: A boundary defect
Explanation: the defects that occur on the surface of a material are known as surface or boundary defects. geometrically, they are regarded as two-dimensional defects.

389. How is the dislocation energy defined?
A. j m-1
B. j m-2
C. m-2
D. n m-1

Answer: A j m-1
Explanation: dislocation energy is defined ad joule per meter and is denoted by e. dislocation density is defined as meter per cubic meter or simply as per meter square.

390. Which one of the following, is a line imperfection?
A. grain boundary
B. tilt boundary
C. dislocation
D. stacking fault

Answer: C dislocation
Explanation: dislocations look like lines in the lattice, which are one dimensional. so it falls under the category of line imperfections. while grain boundary, tilt boundary and stacking fault are surface imperfections.

391. What is the range of dislocation density in pure and unhardened metals?
A. 1010 – 1012 m-2
B. 1014 – 1016 m-2
C. 104 – 106 m-2
D. 108 – 1010 m-2

Answer: A 1010 – 1012 m-2
Explanation: pure unhardened metals (real crystal) contain large number of dislocations of the order of1010 – 1012 m-2. so these can easily be deformed.

392. What is unit of dislocation density?
A. m
B. m-2
C. kg/m3
D. m-3

Answer: B m-2
Explanation: dislocation density is defined as number of lines in a unit volume. so the unit of dislocation density is m/m3 or m-2.

393. 6 BURGER VECTORS, STACKING FAULTS – ROLE OF
A. increase in strength
B. decrease in strength
C. increase or decrease in strength depending on dislocation density
D. don’t affect strength of metal

Answer: C increase or decrease in strength depending on dislocation density
Explanation: if dislocation density is in range 1010 – 1012 m-2, it decreases the strength by easy plastic deformation. on the other hand, if it exceeds to 1016 m-2, these causes strengthening of metal by interaction to imperfections.

394. The number of dislocations increases drastically during
A. solidification
B. plastic deformation
C. elastic deformation
D. heat treatment

Answer: B plastic deformation
Explanation: dislocations increase in number drastically during plastic deformation. it is due to the formation of a frank-read source.

395. Positive edge dislocation is denoted by
A. ↶
B. ↷
C. ꓕ
D. ꓔ

Answer: C ꓕ
Explanation: positive edge dislocation is represented as ‘ꓕ’ (inverted ꓔ) because the extra half plane lies above the shear plane. ‘ꓔ’ is used for negative edge dislocation. ‘↶’ and ‘↷’ are used to represent screw dislocations.

396. Edge dislocation introduces shear strain only.
A. true
B. false

Answer: B false
Explanation: edge dislocations cause compressive, tensile and shear lattice strains.

397. What term is used for the defect, produced by an array of dislocations that produces a small difference in orientation between the adjoining lattices?
A. tilt boundary
B. twist boundary
C. free surface
D. low angle grain boundary

Answer: D low angle grain boundary
Explanation: the array of dislocations produces an angular mismatch between the lattices, which is referred to as low angle grain boundary. these have an angle less than 100.

398. Which statement is false?
A. plastic deformation decreases dislocation density.
B. strain hardening is the increase of dislocation density with plastic deformation.
C. slip plane is the crystallographic plane of dislocation motion.
D. dislocation can change its plane of motion by climb on high temperatures.

Answer: A plastic deformation decreases dislocation density.
Explanation: plastic deformation increases the dislocation density. plastic deformation causes generation of dislocations due to the frank-read source. all other statements are correct.

399. Most crystalline materials have dislocations in their as formed state.
A. true
B. false

Answer: A true
Explanation: crystalline materials have dislocations due to stresses (mechanical, thermal …) associated with the forming processes. thus forming processes are the source of dislocations.

400. Dislocation density can vary from
A. 105 – 1012 cm-2
B. 105 – 1012 m-2
C. 108 – 1010 cm-2
D. 106 – 1010 cm-2

Answer: A 105 – 1012 cm-2
Explanation: dislocation density varies in metals from 105 cm-2 (in carefully solidified metal) to 1012 cm-2 (in heavily deformed metal). it depends on various parameters as degree of deformation, temperature etc.

401. The diagram given below represents which of the following method?
A. bridgman method
B. stockbarger method
C. czochralski method
D. zone melting method

Answer: C czochralski method
Explanation: czochralski method is basically a method for the growth of a single crystal from a melt of the same composition. it is also widely used for the growth of the crystals of semiconducting materials, si, ge, gaas, etc. it has also been used to produce laser generator materials such as ca(nbo3)2 doped with neodymium.

402. In the process of Czochralski method which of the following relation is appropriate between the melt and the growing crystals?
A. melt and the growing crystals are usually not related to each other
B. melt and the growing crystals are usually rotated counterclockwise
C. melt and the growing crystals are usually rotated clockwise
D. melt and the growing crystals are usually kept at a constant position

Answer: B melt and the growing crystals are usually rotated counterclockwise
Explanation: the melt and the growing crystals are usually rotated counterclockwise during pulling in the process of czochralski, in order to maintain a constant temperature, melt uniformity, etc.

403. Which of the following statements is appropriate for Stockbarger method?
A. solidification is achieved by passing the melt through a concentration gradient
B. solidification is achieved by passing the melt through a temperature gradient
C. liquefaction is achieved by passing the melt through a concentration gradient
D. liquefaction is achieved by passing the melt through a temperature gradient

Answer: B solidification is achieved by passing the melt through a temperature gradient
Explanation: stockbarger method is based on solidification of stoichiometric melt but in these, oriented solidification of the melt is achieved by effectively passing the melt through a temperature gradient such that crystallization occurs at the cooler end. thus this method is achieved by arranging for a relative displacement of the melt and a temperature gradient.

404. Which of the following statements describes best the Bridgman method?
A. melt is outside the temperature furnace, solidification begins at the hotter end
B. melt is inside the temperature furnace, solidification occurs at the cooler end
C. melt is inside the temperature furnace, solidification occurs at the hotter end
D. solidification is achieved by passing the melt through a temperature gradient

Answer: B melt is inside the temperature furnace, solidification occurs at the cooler end
Explanation: in the bridgman method, the melt is inside a temperature gradient furnace and the furnace is gradually cooled so that the solidification begins at the cooler end. in this method, it is again advantageous to use a seed crystal and atmospheric control may be necessary.

405. Which one of the following principle has been used in the zone melting method?
A. impurities concentrate in the solid than in liquid phase
B. impurities concentrate in the liquid phase than in gaseous phase
C. impurities concentrate in the liquid phase than in the solid phase
D. impurities concentrate in the gaseous phase than in the solid phase

Answer: C impurities concentrate in the liquid phase than in the solid phase
Explanation: zone melting method make the use of the principle that impurities usually concentrate in the liquid rather than in the solid phase. impurities are therefore ‘swept out’ of the crystal by the moving molten zone. the method has been used for the purification and crystal growth of the high melting metals such as tungsten.

406. Which one of the following statements is correct for precipitation method?
A. growth of the crystal from a solvent of same composition to the crystals
B. growth of the crystal from the solute of same composition to the crystal
C. growth of the crystal from the gaseous species of different composition to the crystal
D. growth of the crystal from a solvent of different composition to the crystals.

Answer: D growth of the crystal from a solvent of different composition to the crystals.
Explanation: in contrast to the methods like

407. In the precipitation method for the growth of the crystal, the solvent melts are often known as
A. electrolyte
B. α-particle
C. β- particle
D. fluxes

Answer: D fluxes
Explanation: in the precipitation method which used for the growth of crystals from the solvent of different composition to the crystals, the solvent melts are often called as fluxes since they effectively reduce the melting point of the crystals by a considerable amount. the method has recently been used to grow crystals of β- and β” alumina solid electrolytes using a borate flux.

408. When was the Verneuil flame fusion method first used?
A. 1207
B. 2016
C. 1503
D. 1904

Answer: D 1904
Explanation: the verneuil flame fusion method was used in 1904 for growing crystals of high melting oxides, including artificial gemstones such as ruby and sapphire.

409. Which of the following method has been used to prepare the single crystals of CaO using plasma torch?
A. stockbarger method
B. zone melting method
C. verneuil flame fusion method
D. bridgman method

Answer: C verneuil flame fusion method
Explanation: verneuil flame fusion method has been recently used to prepare the single crystals of cao with a melting point equal to 2600◦c by using a plasma torch to melt the cao powder. the starting material in the form of a fine powder is passed through an oxyhydrogen flame or some other high temperature torch or furnace after melting has taken place, the droplets fall onto the surface of the growing crystals where they solidify.

410. What is the advantage of using Czochralski, Bridgman- Stockbarger and Verneuil method?
A. gives small crystals
B. high tech apparatus
C. rapid growth rates
D. uses plasma torch

Answer: C rapid growth rates
Explanation: the above methods are melt growth methods which are used for the growth of crystals. advantages of using these melt growth methods are, t gives large crystals, allows rapid growth rates, and requires very simple apparatus. while the disadvantage can be in the crystal quality which can be poor with inhomogeneities and large defect concentrations.

411. What is the disadvantage of using a solution growth method for the growth of the crystals?
A. rapid growth rates
B. simple apparatus
C. slow growth rates
D. isothermal conditions

Answer: C slow growth rates
Explanation: solution growth methods like the water crystallization, flux growth, hydrothermal method etc, which are used for the growth of the crystals have the disadvantage that it leads to very slow growth

Engineering Physics Objective Questions wirh Answers Pdf Download Online Test

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top