250+ TOP MCQs on nMOS and Complementary MOS (CMOS) and Answers

VLSI Multiple Choice Questions on “nMOS and Complementary MOS (CMOS)”.

1. The n-MOS invertor is better than BJT in terms of:
A. Fast switching time
B. Low power loss
C. Smaller overall layout area
D. All the mentioned
Answer: D
Clarification: The n-MOS invertor is better than BJT invertor due to fast switching time, low power loss, smaller overall layout area.

2. The n-MOS invertor consists of n-MOS transistor as driven and
A. Resistor as a load
B. Depletion mode n-MOS as a load
C. Enhancement mode n-MOS as a load
D. Any of the mentioned
Answer: D
Clarification: The n-MOS inverter consists of n-MOS and resistor or depletion mode n-MOS or enhancement mode n-MOS at the pull up load.

3. If the n-MOS and p-MOS of the CMOS inverters are interchanged the output is measured at:
A. Source of both transistor
B. Drains of both transistor
C. Drain of n-MOS and source of p-MOS
D. Source of n-MOS and drain of p-MOS
Answer: A
Clarification: When the transistors are interchanged, The drain of n-MOS is connected to supply voltage, drain of p-MOS is connected to the ground. The output is measured at source of both the transistors.

4. What will be the effect on output voltage if the positions of n-MOS and p-MOS in CMOS inverter circuit are exchanged?
A. Output is same
B. Output is reversed
C. Output is always high
D. Output is always low
Answer: B
Clarification: When the input is low, p-MOS is ON and the output is pulled down to the ground. When the input is high, n-MOS is ON and the output is pulled up to the supply voltage.

  250+ TOP MCQs on Scan Design Techniques-1 and Answers

5. The average power dissipated in resistive load n-MOS inverter is:
A. 0
B. VDD (VDD-VOL)/R
C. VDD (VDD-VOL)/2R
D. VDD (VDD-VIH)/2R
Answer: C
Clarification: When the input voltage is equal to VOH on the other hand, both the driver MOSFET and the load resistor conduct a nonzero current. Since the output voltage in this case is equal to VOL, DC power consumption of the inverter can be estimated as VDD (VDD-VOL)/2R.

6. The depletion mode n-MOS as an active load is better than enhancement load n-MOS in:
A. Sharp VTC transition and better noise margins
B. Single power supply
C. Smaller overall layout area
D. All of the mentioned
Answer: D
Clarification: The depletion mode n-MOS transistor as load requires single power supply, smaller overall layout area, and sharp VTC transition.

7. The enhancement mode n-MOS load inverter requires 2 different supply voltages to:
A. Keep load transistor in cutoff region
B. Keep load transistor in linear region
C. Keep load transistor in saturation region
D. None of the mentioned
Answer: B
Clarification: The enhancement mode n-MOS load inverter requires 2 different supply voltages to keep load transistor in linear region.

8. The CMOS inverter consists of:
A. Enhancement mode n-MOS transistor and depletion mode p-MOS transistor
B. Enhancement mode p-MOS transistor and depletion mode n-MOS transistor
C. Enhancement mode p-MOS transistor and enhancement mode p-MOS transistor
D. Enhancement mode p-MOS transistor and enhancement mode n-MOS transistor
Answer: D
Clarification: The CMOS inverter consist of enhancement mode p-MOS and enhancement mode n-MOS.

  250+ TOP MCQs on Switch Logic and Answers

9. In the CMOS inverter the output voltage is measured across:
A. Drain of n-MOS transistor and ground
B. Source of p-MOS transistor and ground
C. Source of n-MOS transistor and source of p-MOS transistor
D. Gate of p-MOS transistor and Gate of n-MOS transistor
Answer: A
Clarification: In the CMOS inverter the output voltage is measured across Drain of n-MOS transistor and ground.

10. When the input of the CMOS inverter is equal to Inverter Threshold Voltage Vth, the transistors are operating in:
A. N-MOS is cutoff, p-MOS is in Saturation
B. P-MOS is cutoff, n-MOS is in Saturation
C. Both the transistors are in linear region
D. Both the transistors are in saturation region
Answer: D
Clarification: When the input of the CMOS inverter is equal to Inverter Threshold Voltage Vth, both the transistors are operating in saturation region

11. The switching threshold voltage VTH for an ideal inverter is equal to:
A. (VDD-VOL)/2
B. VDD
C. (VDD./2
D. 0
Answer: C
Clarification: The switching threshold voltage VTH for an ideal inverter is equal to (VDD./2.

12. Which of these invertors is more efficient?
vlsi-questions-answers-nmos-cmos-q12″>vlsi-questions-answers-nmos-cmos-q12
A. Depletion mode n-MOS inverter
vlsi-questions-answers-nmos-cmos-q12a”>vlsi-questions-answers-nmos-cmos-q12a
B. pMOS inverter
vlsi-questions-answers-nmos-cmos-q12b”>vlsi-questions-answers-nmos-cmos-q12b
C. CMOS inverter
vlsi-questions-answers-nmos-cmos-q12c”>vlsi-questions-answers-nmos-cmos-q12c
D. Resistive load nMOS inverter
Answer: C
Clarification: The power loss in CMOS inverter is very small and the I-V characteristics is approximately equal to ideal inverter. Therefore the CMOS inverter is most efficient.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top