Heat Transfer Questions & Answers for experienced on “Heat Dissipation From An Infinitely Long Fin “.
1. In heat dissipation from an infinitely long fin, the boundary conditions are
a) t = t0 at x = infinity and t = ta at x = 0
b) t = t0 at x = 0 and t = ta at x = infinity
c) t = t0 at x = 0 and t = ta at x = 0
d) t = t0 at x = infinity and t = ta at x = infinity
Answer: b
Clarification: These conditions must be approached when ml is greater than 5.
2. The temperature distribution in case of infinitely long fin is
a) t – t a/t 0 – t a = mx
b) t – t a/t 0 – t a = -mx
c) t – t a/t 0 – t a = e-m x
d) t – t a/t 0 – t a = log (m x)
Answer: c
Clarification: Exponential curve should be here.
3. The rate of heat transfer in case of infinitely long fin is given by
a) (h P k A) 1/2 (t 0 – t a)
b) (h P A) 1/2 (t 0 – t a)
c) (P k A) 1/2 (t 0 – t a)
d) (h k A) 1/2 (t 0 – t a)
Answer: a
Clarification: It should contain all the terms i.e. h, p, k and A.
4. Let us say there are two rods having same dimensions, one made of brass (k = 85W/m K) and the other of copper (k = 375W/m K), having one of their ends inserted into a furnace. At a section 10.5 cm away from the furnace, the temperature of brass rod is 120 degree Celsius. Find the distance at which the same temperature would be reached in the copper rod? Both ends are exposed to the same environment
a) 12.54 cm
b) 45.87 cm
c) 12.34 cm
d) 22.05 cm
Answer: d
Clarification: For brass rod, 120 = t a + (t 0 – t a) e –m l and for copper rod, 120 = t a + (t 0 – t a) e –M L So L = L 0 (k 2/k 1) = 22.05 cm.
5. Three rods, one made of silver (l = 420W/m K), second made of aluminum (k = 210W/m K) and the third made of iron (k = 70W/m K) are coated with a uniform layer of wax all around. The rods are placed vertically in a boiling water bath with 250 mm length of each rod projecting outside. If all the rods are having following dimensions i.e. diameter = 15 mm and length = 300 mm and have identical surface coefficient 12.5W/ m2 K, work out the ratio of lengths up to which wax will melt on each rod
a) 2.45:1:1.732
b) 1.732:1:2.45
c) 2.45:1.732:1
d) 1.732:1:2.45
Answer: c
Clarification: k 1/l 12 = k 2/l 22 = k 3/l 32.
6. Let us assume there are two pieces of copper wire 0.1625 cm in diameter with a device that melts it at 195 degree Celsius. The wires are positioned vertically in air at 24 degree Celsius and the heat transfer coefficient of the wire is 17 W/ square m K. Let us say k = 335W/m K i.e. of wire. Find out the energy input?
a) 1.234W
b) 2.652W
c) 4.562W
d) 9.435W
Answer: b
Clarification: A C = π D 2/4 = 2.073 * 10 –6square meter. P = π D = 0.0051 m. Q FIN = k A C m (t2 – t 1) = 1.326W.
7. A rod of 10 mm square section and 160 mm length with thermal conductivity of 50W/m K protrudes from a furnace wall at 200 degree Celsius with convective coefficient 20 W/ square m K. Make calculations for the heat convective up to 80 mm length
a) 6.84W
b) 7.34W
c) 4.54W
d) 5.47W