Statistical Quality Control Multiple Choice Questions on “Attribute Charts – Control Charts for Nonconformities (Defects) – 1”.
1. The event of a specification not satisfied at one point of a product, is called ____________
a) Nonconformity
b) Non-defectiveness
c) Un-specification
d) Non-specification
Answer: a
Clarification: Each event, in which a specification is not satisfied or an error occurs in approaching the specification value, is called nonconformity or a defect.
2. A nonconforming item has at least ____________ conformities.
a) 4
b) 3
c) 1
d) 2
Answer: c
Clarification: A nonconforming item is defined as the item or product, which has at least one defect. It is necessary that a nonconforming item has one or more than one defects.
3. The c-control chart is plotted for _____________
a) Fraction nonconforming
b) Number of nonconformities per unit
c) Number of defects observed
d) Deviation from median of the defects in samples
Answer: c
Clarification: The c-control chart is based on the total number of nonconformities in a product unit of a process output. So a c-chart is also called control chart for nonconformities.
4. Which of these is an assumption made for designing a control chart for noncorformities?
a) Normal Distribution
b) Poisson Distribution
c) Lognormal Distribution
d) Weibull Distribution
Answer: b
Clarification: The control charts for nonconformities, make an assumption that the sample taken is well modeled by the Poisson distribution. This is a necessary assumption to deal with these control charts.
5. Which of these is not an assumption of the c-chart?
a) Number of potential locations for nonconformities should be large
b) Probability of occurrence of nonconformities should be small
c) Probability of occurrence of nonconformities should be variable
d) Probability of occurrence of nonconformities should be constant
Answer: c
Clarification: The assumption of Poisson distribution of nonconformities in the samples of constant size, for c-charts, makes it necessary that, number of potential locations for nonconformities should be large, and the probability of occurrence of nonconformities should be small and constant.
6. What will be the value of the 3-sigma Upper control limit for the c chart when standard is given?
a) UCL = c + 3√c
b) UCL = c – √c
c) UCL = c + √c
d) UCL = c + 2√c
Answer: a
Clarification: The 3 – sigma upper control limit for the c-chart is expressed algebraically by
UCL = c + √c.
7. The center line for the control chart for nonconformities is representing the value equal c, which is ____________
a) The total number of nonconformities
b) The average number of conformities in a preliminary sample
c) The total number of nonconforming products
d) The total number of conforming products
Answer: b
Clarification: If there is no standard given for the c-chart, the center line represents the estimation of standard, c which is equal to the average number of nonconformities in a preliminary sample.
8. When there is no standard given, the value of LCL for the c-chart is given by ___________
a) LCL=(bar{c}-3sqrt{bar{c}})
b) LCL=(bar{c}+2sqrt{bar{c}})
c) LCL=(bar{c}-2sqrt{bar{c}})
d) LCL=(bar{c}+3sqrt{bar{c}})
Answer: d
Clarification: When there is no standard given for the number of conformities (c), for the c chart, the lower control limit is given by,
LCL=(bar{c}+3sqrt{bar{c}})
9. If the average number of nonconformities in a preliminary sample of a process is 19.67, which of these represents the value of UCL for a c-chart for this process output?
a) 19.67
b) 6.37
c) 32.97
d) 25.77
