250+ TOP MCQs on Different Types of Multivibrators – 2 and Answers

Analog Circuits Multiple Choice Questions on “Different Types of Multivibrators – 2”.

I have to say that i've been using the bactrim for three years and i've never had an allergic reaction to it and never had my dog have one. Cytotec comes as a solution and is administered through a needle inserted into buy provigil online with prescription civilly a muscle. It is marketed by the company jual malaysia, and is available for tooth repair and restoration.

1. Given the following circuit.

The supply voltage being applied is ±15V. The diode cut-in voltage is 0.7V. Find the maximum value of R such that circuit can behave as a monostable multivibrator.
A. 612.8kΩ
B. 33kΩ
C. 220.22kΩ
D. 450.8kΩ

Answer: A
Clarification: The condition to be followed is βV_Sat > V_Y.
β = R1/R1+R2 = 30k/30k+R
Thus (30k/30k+R). 15 > 0.7
450k/30k + R > 0.7
30k+R < 642.85k
R < 612.8kΩ.

2. For the given circuit, find the time period of the output waveform, given that the diode is used is of Silicon and the supply voltage being applied is ±15V. The feedback factor is 0.4.

A. 11.12 ms
B. 12.4 ms
C. 11.2 seconds
D. 5.6 ms

Answer: a
Clarification: T = RCln(1+V_γ/V_Sat/1-β)
T = 10x2x10^-3xln((1+0.7/15)/0.6) = 20×10^-3ln(1.0467/0.6)=20×0.556×10^-3
T = 11.12 ms.

3. Find the approximate frequency of output waveform of a monostable multivibrator given that RC = 20×10^-3 and feedback factor = 0.3.
A. 200Hz
B. 142Hz
C. 233Hz
D. Can’t be found out without supply voltage value

Answer: B
Clarification: T = RCln(1/1-β)
T = 20×10^-3 x ln(1/0.7) = 20×0.35×10^-3 = 7ms
f = 0.142 kHz = 142 Hz.

4. Consider the circuit shown below.

R1=5kΩ, R2=5kΩ, R3=5kΩ, R4=10kΩ, R5=20kΩ, C1=10μF. Calculate the total charging time and discharging time.
A. The charging time = 0.2 seconds, the is charging time is 0.2 seconds
B. The charging time = 0.3 seconds, the discharging time is 0.2 seconds
C. The charging time = 0.3 seconds, the discharging time is 0.3 seconds
D. The charging time = 0.5 seconds, the discharging time is 0.4 seconds

Answer: B
Clarification: Discharge time = R5.C1 = 20x10x10^-3 = 0.2 seconds
Charging time = (R4+R5)C1 = 30x10x10^-3 = 0.3 seconds.

5. For the given circuit, find the duty cycle of the output.

R4=30kΩ, R5=25kΩ.
A. 0.6875
B. 0.7211
C. 0.5681
D. 0.5010

Answer: A
Clarification: Duty cycle = T_High/T_O
Duty cycle = R4+R5/R4+2xR5
Duty cycle = 55/80= 0.6875.

6. What is the output frequency for the following circuit?

R4=30kΩ, R5=40kΩ, C1=5nF.
A. 2.63 kHz
B. 3kHz
C. 263 kHz
D. 4.4 kHz

Answer: A
Clarification: Output frequency = 1.45/(R4+2xR5)xC1
f_O = 1.45×1000000/110×5 = 2.63 kHz.

7. In the astable multivibrator using IC 555, it can be used as a voltage to frequency converter.
A. True
B. False

Answer: A
Clarification: An astable multivibrator can be easily used as a voltage controlled oscillator or as a voltage to frequency converter if a control voltage is applied to the control pin of the IC. The control pin is usually grounded through a capacitor if unused.

8. How can a monostable multivibrator using IC 555 be used as a PWM generator?
A. If a diode is connected across the resistor RA
B. If a modulating signal m(t) is applied at the control pin
C. If the control pin is always kept high
D. It cannot be used as a PWM generator ever

Answer: C
Clarification: A monostable multivibrator can be used as a PWM generator if a modulating signal is applied to the control pin. The control pin is used to vary the voltage at the inverting node of the upper comparator. If unused, then the control pin is grounded through a capacitor.

9. Given that the charging current of capacitor is constant in a monostable multivibrator using IC 555, then find the type of output waveform, type of capacitor voltage waveform and the time period of output.
A. The capacitor waveform is a ramp, the output waveform is sinusoidal, the time period is (frac{2.C.VCC}{3.I})
B. The capacitor waveform is a ramp, the output waveform is a pulse, the time period is (frac{2.C.VCC}{3.I})
C. The capacitor waveform is a ramp, the output waveform is a pulse, the time period is (frac{C.VCC}{3.I})
D. The capacitor waveform is a ramp, the output waveform is a ramp, the time period is (frac{2.C.VCC}{3.I})

Answer: B
Clarification: If a constant charging current is applied through the capacitor, the output is a pulse, while capacitor voltage is a ramp.
Time period of ramp/pulse = T_O = 2V_CCxC/3I.