Statistical Quality Control Multiple Choice Questions on “Gauge and Measurement System Capability Studies – 3”.
1. SNR represents __________
a) Sign to noise ratio
b) Sample to nonconforming ratio
c) Size to noise ratio
d) Signal to noise ratio
Answer: d
Clarification: A measure of measurement system adequacy is defined by AIAG, which is called SNR or signal to noise ratio. It is used to check the satisfactoriness of the measurement system.
2. SNR is equal to _________
a) (sqrt{frac{2ρ_p}{1-ρ_p}})
b) (sqrt{frac{3ρ_p}{1-ρ_p}})
c) (sqrt{frac{ρ_p}{1-ρ_p}})
d) (frac{2ρ_p}{1-ρ_p})
Answer: a
Clarification: SNR is the measure of measurement system adequacy. It uses the gauge capability ratio ρp. It is expressed as,
SNR=(sqrt{frac{2ρ_p}{1-ρ_p}})
3. What is the correct definition of SNR?
a) The number of signals for 30 noise indications on control chart
b) The number of signals for single noise indication on control chart
c) The number of signals with no noise from the measurements
d) The number of distinct levels or categories that can be reliably obtained from the measurements
Answer: d
Clarification: SNR is defined by AIAG as the number of distinct levels or categories that can be reliably obtained from the measurement.
4. If the estimate of pp is 0.9214, what will be the estimate of SNR?
a) 4.84
b) 6.87
c) 9.12
d) 2.13
Answer: a
Clarification: We know that,
SNR=(sqrt{frac{2ρ_p}{1-ρ_p}})
By putting the value of the estimate of ρp we get SNR estimate = 4.84.
5. Which of these is not one of the gauge capability ratios?
a) SNR
b) Cp
c) ρM
d) ρp
Answer: d
Clarification: SNR, ρp and ρM are some examples of the gauge capability ratios, which are used to check the adequacy of the measurement system used.
6. What is the full-form of DR in the context of gauge capability?
a) Decrease rate
b) Direction ratios
c) Discrimination ratios
d) Dimension rates
Answer: c
Clarification: Like the other gauge capability ratios like SNR, ρp, and ρM; DR is also a measure of gauge capability. Its full-form is known as discrimination ratio.
7. What is the value of DR?
a) DR=(frac{1-2ρ_p}{1+ρ_p})
b) DR=(frac{1+ρ_p}{1-ρ_p})
c) DR=(frac{1+2ρ_p}{1-ρ_p})
d) DR=(frac{1-ρ_p}{1+ρ_p})
Answer: d
Clarification: The value of the discrimination ratio, which is used as a measure of adequacy of a measurement system, and which uses the ratio ρp, is used to evaluate the gauge capability. It is expressed as,
DR=(frac{1-ρ_p}{1+ρ_p})
8. For a measurement system ρp=0.8914. What will be the value of DR for that?
a) 17.416
b) 0.0571
c) 24.46
d) 0.0652
Answer: a
Clarification: We know that,
DR=(frac{1-ρ_p}{1+ρ_p})
Putting the values, we get DR=17.416.
9. For a gauge to be capable, generally DR must be greater than ___________
a) 1
b) 0.4
c) 0.1
d) 4
Answer: d
Clarification: It is generally stated that the DR for a capable gauge is, generally having a value higher than 4. This means for a gauge to be capable, the DR must exceed 4.
10. Which of these tells about the inherent variability of the gauge?
a) Accuracy
b) Precision
c) DR ratio
d) SNR
